|
Error Codes | FRU/Action |
---|---|
107 System board, processor | 1. Flash BIOS |
update error. (A-2 system board only) | 2. System Board |
10X System board error or | 1. System Board |
continuous beep. | |
110 System board parity error | 1. see 'Memory' |
2. DIMMs | |
3. System Board | |
111 I/O channel parity error | 1. see 'Memory' |
2. I/O channel memory | |
3. System Board | |
114 External ROM checksum error | 1. Adapter Card |
2. System Board | |
129 Cache memory error | 1. see 'Memory' |
2. For A-1 system board: | |
° System Board | |
For A-2 system board: | |
° Processor | |
12X Processor error | 1. Run the Setup Utility, see |
'POST Error Codes' | |
2. Processor | |
3. System Board | |
13X System board error. | 1. Run the Setup Utility, see |
'POST Error Codes' | |
2. Processor | |
3. System Board | |
151 Real-time clock failure | 1. System Board |
161 Low CMOS battery | 1. CMOS clock/battery (if less than 2.8 Vdc) |
2. Run the Setup Utility, see 'POST Error Codes' | |
3. System Board | |
162 CMOS RAM error. | 1. CMOS clock/battery (if less than 2.8 Vdc) |
2. Run the Setup Utility, see 'POST Error Codes' | |
3. System Board | |
163 Real-time clock error. | 1. Set date and time |
2. Run the Setup Utility, see 'POST Error Codes' | |
3. CMOS clock/battery (if less than 2.8 Vdc) | |
4. System Board | |
164 Memory size error. | 1. see 'Memory' |
2. DIMMs | |
3. System Board | |
1XX errors not listed above | 1. System Board |
20X Memory error. | 1. see 'Memory' |
2. DIMMs | |
3. System Board | |
262 DRAM parity config. error. | 1. see 'Memory' |
2. Run the Setup Utility, see 'POST Error Codes' | |
3. DIMMs | |
4. System Board | |
305 System board | 1. see 'Keyboard' |
non-replaceable fuse can be blown | 2. Keyboard |
by a defective KBD, KBD-cable, | 3. Keyboard connection/cable |
or mouse. If you suspect one | 4. Mouse |
of these FRUs, replace it when | 5. System Board |
you replace the system board. | |
3XX Keyboard error | 1. see 'Keyboard' |
2. Keyboard connection | |
3. Keyboard | |
4. Media Console (Type 2142) | |
5. System Board | |
602 Invalid diskette boot record | 1. Diskette media |
2. Diskette connection/cable | |
3. Diskette drive | |
662 Diskette drive config. error | 1. see Factory-Installed Drive Devices |
2. Diskette connection/cable | |
3. Diskette drive | |
4. Power supply | |
5. System Board | |
7XX Math coprocessor error | 1. see Diagnostics and Utilities Device Presence Test' |
2. Upgrade processor (check Setup Utility, and | |
system board settings.) | |
3. System Board | |
962 Parallel port conflict | 1. Test using a wrap plug while running |
Diagnostics and Utilities | |
2. see Diagnostics and Utilities Device Presence Test' | |
3. Parallel adapter card, if installed | |
4. System Board | |
11XX Serial port test errors | 1. Test using a wrap plug while running |
not listed above. | Diagnostics and Utilities |
2. see Diagnostics and Utilities Device Presence Test' | |
3. Serial adapter card, if installed | |
4. System Board | |
On the system board : | 1. Hard Disk drive connection/cable/jumpers. |
1780/1790 Hard Disk Drive 0 | If an upgradable processor is installed, check that the |
1781/1791 Hard Disk Drive 1 | proper speed has been set. |
1782/1792 Hard Disk Drive 2 | (switches and Setup Utility). Speed should be a |
or CD/DVD-ROM drive | multiple of the original processor speed. |
1783/1793 Hard Disk Drive 3 | Hard disk drive size set correctly in Setup Utility. |
or CD/DVD-ROM drive | 2. Hard disk drive |
if Hard Disk Drive 2 installed. | 3. System Board |
17XX Hard disk drive error | 1. see 'Factory-Installed Drive Devices' |
(All 17XX errors not listed above) | 2. Hard disk drive jumpers |
3. Hard disk drive connection/cable | |
4. Hard disk drive | |
5. System Board | |
6. Power Supply | |
1800 PCI Error (IRQ not available) | A PCI adapter card has requested a hardware |
interrupt that is not available | |
1. Choose ISA Legacy Resources from the Setup Utility | |
main menu, and make sure the interrupt resources (IRQ) | |
setting for ISA legacy adapter cards are correct. If the | |
interrupt resources settings are not correct, change the | |
settings. See 'Using the Setup Utility' | |
2. If all interrupt are being used by ISA legacy adapter cards, | |
you might need to remove an ISA card to make memory available | |
to the PCI adapter card. | |
1801 PCI Error (ROM not available) | A PCI adapter card has requested memory resources |
that are not available | |
1. Choose ISA Legacy Resources from the Setup Utility | |
main menu, and make sure the memory resources settings | |
for ISA legacy adapter cards are correct. If the memory | |
resources settings are not correct, change the settings. | |
2. If all memory resources are being used by ISA legacy adapter | |
cards you might need to remove an ISA card to make memory | |
available to the PCI adapter card. | |
1802 PCI Error | A PCI adapter card has requested an I/O address |
(I/O address not available) | that is not available, or the PCI adapter card might |
be defective. | |
1. Choose ISA Legacy Resources from the Setup Utility | |
main menu, and make sure the I/O port resources (IRQ) | |
settings for ISA legacy adapter cards are correct. If the | |
I/O port resources settings are not correct, change the | |
settings. | |
2. If the I/O port resources settings are correct, the PCI | |
adapter card might be defective. | |
1803 PCI Error | A PCI adapter card has requested a memory address |
(memory above 1 MB not available) | that is not available, or the PCI adapter card might |
be defective. | |
1. Choose ISA Legacy Resources from the Setup Utility | |
main menu, and make sure the memory resources settings | |
for ISA legacy adapter cards are correct. If the memory | |
resources settings are not correct, change them. | |
2. If the memory resources settings are correct, the PCI | |
adapter card might be defective. | |
1804 PCI Error | A PCI adapter card has requested a memory address |
(memory below 1 MB not available) | that is not available. |
1. Choose ISA Legacy Resources from the Setup Utility | |
main menu, and make sure the memory resources settings | |
for ISA legacy adapter cards are correct. If the settings | |
are not correct, change the settings. | |
2. If all memory resources are being used by ISA legacy adapter | |
cards, you might need to remove an ISA card to make memory | |
available to the PCI adapter card. | |
1805 PCI Error (ROM error). | 1. Remove the PCI adapter card. |
2. Restart the computer without the card installed. If the computer | |
restarts without an error, reinstall the card and restart the | |
computer again. | |
If the error reoccurs, the adapter might be defective. | |
1806 No more DMA channels available | 1. Too many adapters installed. |
2401 Monitor changing colors | 1. Monitor |
2462 Video configuration error | 1. Video memory, if installed |
2. System Board | |
24XX Video/monitor error | 1. see 'Monitor' |
2. Optional video memory | |
3. System Board | |
4. Monitor | |
5801 Media Console error | 1. Check Media Console cable |
2. replace Media Console | |
5803 Keyboard error | 1. see 'Keyboard' |
attached to Media Console | 2. Keyboard |
5806 Diskette error | 1. Check Diskette cable |
attached to Media Console | 2. Diskette |
5859 CD/DVD-ROM error | 1. Check CD/DVD-ROM drive cable |
attached to Media Console | 2. CD/DVD-ROM Drive |
5862 Host Card error | 1. Host Card |
5886 Pointing device | 1. Check Pointing device cable |
attached to Media Console | 2. Pointing device |
5962 CD/DVD-ROM | 1. see 'Factory-Installed Drive Devices' |
configuration error (sound adapter | 2. CD/DVD-ROM drive connections, cables, and jumpers |
card driver works correctly). | 3. CD/DVD/-ROM drive |
4. Power supply | |
5. System Board | |
86XX Pointing device | 1. see 'Mouse' |
error or mouse does not work. | 2. Pointing device connection/cable |
card driver works correctly). | 3. Pointing device |
4. System Board | |
I999030X | 1. Possible hard disk drive problem |
Hard disk reset/boot failed | 2. see 'Hard Disk Drive Boot Error' |
Any other error codes | see 'Undetermined Problem' |
Please see the LEGAL - Trademark notice.
Feel free - send a for any BUG on this page found - Thank you.