|
|
|
Error Codes 62xx-65xx/68xx, Server 315-8638 and 2134-2176 Aptiva
If machine type is 2134 or 2176 then for FRU/Action you should choose ISA Legacy Resources from the
Setup Utility main menu, and make sure the Memory / IRQ settings for ISA legacy adapters
are correct.
| Error Code: | FRU/Action. |
|---|---|
| 000 SCSI Adapter not enabled | 1. Be sure that the adapter Device and Bus |
| Master fields are enabled in PCI | |
| configuration program. Refer to the | |
| documentation that was shipped with | |
| the computer. | |
| 02X | 1. SCSI Adapter |
| 08X | 1. SCSI Cable |
| Check SCSI terminators | 2. SCSI Terminator |
| for proper installation. | 3. SCSI Device |
| 4. SCSI Adapter | |
| 101 | 1. System Board |
| System board interrupt failure | |
| 102 | 1. System Board |
| System board Timer error | |
| 106 | 1. System Board |
| 110 | 1. Memory Module (SIMMs/DIMMs) |
| System board memory parity error | 2. System Board |
| 10X | 1. System Board |
| System board error or | |
| continuous beep | |
| 111 | 1. Reseat Adapters |
| I/O channel parity error | 2. Any Adapter |
| 3. Riser Card | |
| 4. System Board | |
| 114 | 1. Adapter Memory Module |
| Adapter ROM (checksum) error | 2. Any Adapter |
| 3. Riser Card | |
| 4. System Board | |
| 129 | 1. Processor |
| Internal cache test error | 2. L2 Cache Memory |
| 3. System Board | |
| 12X 13X | 1. Processor |
| Processor Error | 3. System Board |
| 151 | 1. System Board |
| Real-time clock failure | |
| 161 | 1. Run Setup |
| Low CMOS battery (< 2.8Vdc) | 2. CMOS (Clock) Battery |
| 3. System Board | |
| 162 | 1. Run Setup and verify Configuration |
| Configuration mismatch. | 2. Had a device been added, removed, changed |
| location ? If not, suspect that device. | |
| 3. Power-on external devices first, then | |
| power-on computer. | |
| 4. CMOS (Clock) Battery (< 2.8Vdc) | |
| 5. System Board | |
| 162 | 1. Diskette Drive |
| And unable to run diagnostics | 2. System Board |
| 3. Diskette Drive Cable | |
| 163 | 1. Time and Date Set ? |
| Clock not updating or | 2. CMOS (Clock) Battery (< 2.8Vdc) |
| invalid time set | 3. System Board |
| 164 | 1. Run Setup. The System Summary |
| POST detected a base memory or | menu will indicate if the |
| extended memory size mismatch error. | size changed. |
| See 'Setup Utility Program' | |
| 2. Run the Extended Memory Diagnostic tests. | |
| 3. SIMMs | |
| 166 | 1. Run Flash Recovery using Boot Block |
| Boot Block Check Sum Error | See 'System Board Location' and |
| 'Flash Recovery Boot Block Jumper' | |
| 2. System Board | |
| 167 | 1. Run Setup. Check Stepping level for the |
| Microprocessor installed that | BIOS needed, then perform the flash update |
| is not supported by the current | 2. Processor |
| POST/BIOS. | |
| 168 | 1. Run Setup. Check to see that Ethernet |
| Alert on LAN error | and Alert on LAN are enabled. |
| System Board | |
| Riser Card (if installed) | |
| 175 | 1. Run Configuration |
| Type 6562, 6592 | See 'Setup Utility Program' |
| 2. Riser Card | |
| 3. System Board | |
| 176 | 1. Covers were removed from |
| the computer. | |
| 177 | 1. Riser Card |
| Corrupted Administrator Password | 2. System Board |
| 178 | 1. Riser Card |
| 2. System Board | |
| 17X 18X | 1. C2 Security |
| 183 | 1. Enter the administrator password |
| 184 | 1. Enter new password |
| Password removed due to | |
| check-sum error. | |
| (See next 184 for Type | |
| 6862, 6889, 6892) | |
| 184 | 1. Make sure Asset Care and Asset ID |
| Type 6862, 6889, 6892 | are enabled in Configuration/Setup |
| No RFID Antenna | 2. RFID Antenna |
| See AssetCare - RFID | 3. System Board |
| 185 | 1. Set configuration and reinstall |
| Corrupted boot sequence | the boot sequence. |
| 186 | 1. Riser Card (if installed) |
| Type 6562,6592,6862,6889,6892 | 2. System Board |
| 187 | 1. Clear Administration Password |
| 2. System Board | |
| 189 | 1. More than three password attempts |
| were made to access the computer | |
| 190 | 1. System Board |
| Chassis intrusion detector was cleared | 2. Riser Card (if installed) |
| This is information only, no | |
| action required. | |
| 1XX | 1. System Board |
| Not listed above | |
| 201 20X | 1. Run Enhanced Diag. Memory Test |
| Memory data error | 2. Memory Module (SIMM/DIMM) |
| 3. System Board | |
| 221 | 1. SIMMs |
| Shadow RAM error | 2. I/O Channel Memory |
| 3. System Board | |
| 225 | 1. Unsupported Memory |
| SIMM installed in wrong socket | |
| 228 | 1. Optional cache tag address module |
| External cache tag RAM error | |
| 229 | 1. L2 Cache Memory |
| External cache memory test error | 2. System Board |
| 262 | 1. Run Setup. The System Summary |
| POST detected a base memory or | menu will indicate type |
| extended memory type error. | memory type changed. |
| DRAM parity configuration error. | See 'Setup Utility Program' |
| 2. Run the Extended Memory Diagnostic tests. | |
| 3. System Board | |
| 264 | 1. L2 Cache Tag Address Module |
| External cache memory size error | and RAM |
| 2. System Board | |
| 301 | 1. Keyboard |
| 2. Keyboard Cable | |
| 3. System Board | |
| 303 | 1. Mouse |
| With an 8603 error | 2. Keyboard |
| 3. Keyboard Cable | |
| 4. System Board | |
| 303 | 1. Keyboard |
| With no 8603 error | 2. Keyboard Cable |
| 3. System Board | |
| 305 | 1. Keyboard |
| Non replaceable fuse (+5Vdc)can | 2. Keyboard Cable |
| be blown by a defective keyboard, | 3. Mouse |
| or mouse. If you suspect one of these | 4. System Board |
| FRUs, replace it when you replace | |
| the system board. | |
| 3XX | 1. Keyboard |
| Not listed above | 2. Keyboard Cable |
| 3. System Board | |
| 5XX | 1. Video Adapter (if installed) |
| 2. System Board | |
| 601 | 1. Diskette Drive A |
| Diskette Drive controller error | 2. Diskette Drive Cable |
| 3. System Board | |
| 601 | 1. Diskette Drive A |
| Type 6562,6592,6862,6889,6892 | 2. Diskette Drive Cable |
| 3. Riser Card (if installed) | |
| 4. System Board | |
| 602 | 1. Bad Diskette ? |
| 2. Verify Diskette and retry. | |
| 604 | 1. Run Setup and verify diskette configuration settings |
| And able to run diagnostics | 2. Diskette Drive B |
| 3. Diskette Drive Cable | |
| 4. Riser Card if drive cable connected | |
| 5. System Board | |
| 605 | 1. Diskette Drive B |
| POST cannot unlock the | 2. Diskette Drive Cable |
| diskette drive | 3. System Board |
| 61X | 1. Diskette Drive |
| Diskette drive test error | 2. Diskette Drive Cable |
| 3. System Board | |
| 62X | 1. Reformat Test Diskette |
| Diskette drive test error | 2. Diskette Drive Cable |
| 3. Diskette Drive | |
| 4. System Board | |
| 662 | 1. Diskette Drive configuration |
| error or wrong diskette drive | |
| type, run Set Configuration. | |
| 2. Diskette Drive | |
| 3. Power Supply | |
| 4. System Board | |
| 6XX | 1. Diskette Drive |
| Not listed above | 2. Diskette Drive Cable |
| 3. Power Supply | |
| 4. System Board | |
| 5. External Drive Adapter | |
| 762 | 1. Run Configuration/Setup |
| Math Coprocessor configuration | 2. Math Coprocessor |
| error | 3. Run Diagnostic |
| 4. System Board | |
| 7XX | 1. Processor / Math Coprocessor |
| Not listed above | 2. Upgrade processor (check Setup Utility, |
| and system board settings). | |
| 3. System Board | |
| 962 | 1. Run Configuration |
| Parallel Port configuration error | 2. Parallel adapter (if installed) |
| 3. Riser Card | |
| 4. System Board | |
| 90X | 1. Parallel Port |
| Parallel Port Test Error | |
| 2. System Board | |
| 9XX | 1. Printer |
| 2. System Board | |
| 1047 | 1. 16-Bit AT Fast SCSI Adapter |
| 107X | 1. Check SCSI terminators for |
| Check for proper installation | proper installation. (act./passive termination ?) |
| of SCSI terminators. | 2. SCSI Cable |
| 3. SCSI Terminator | |
| 4. SCSI Device | |
| 5. SCSI Adapter | |
| 1101 | 1. Run Advanced Diagnostics |
| Serial connector error | |
| possible system board | |
| failure | |
| 1101 1102 1106 | 1. System Board |
| 1108 1109 | 2. Any Serial Device |
| 1102 | 1. Run Advanced Diagnostics |
| Card selected feedback error | |
| 1103 | 1. Run Advanced Diagnostics |
| Port fails register check | 2. System Board |
| 1106 | 1. Run Advanced Diagnostics |
| Serial option cannot | 2. System Board |
| be turned off | |
| 1107 | 1. Serial Device Cable |
| 2. System Board | |
| 1110 | 1. Run Advanced Diagnostics |
| Register test failed | 2. System Board |
| 1116 | 1. Run Advanced Diagnostics |
| Interrupt error | |
| 1117 | 1. Run Advanced Diagnostics |
| Failed baud rate test | |
| 1162 | 1. Run Configuration |
| Serial port configuration error | 2. Serial Adapter (if installed) |
| 3. System Board | |
| 11XX | 1. Serial Port |
| Not listed above | 1. System Board |
| 1201 | 1. System Board |
| 2. Any Serial Device | |
| 1202 1206 1208 | 1. Dual Async Adapter/A |
| 1209 12XX | 2. System Board |
| 3. Any Serial Device | |
| 1207 | 1. Communications Cable |
| 2. Dual Async Adapter/A | |
| 13XX | 1. Game Adapter |
| 1402 | Information only |
| Printer not ready | |
| 1403 | Information only |
| No paper error, or | |
| interrupt failure | |
| 1404 | 1. Run Advanced Diagnostics |
| System board timeout failure | |
| 1405 | 1. Run Advanced Diagnostics |
| Parallel adapter error | |
| 1406 | 1. Run Advanced Diagnostics |
| Presence test error | |
| 14XX | 1. Printer |
| Not listed above, | 2. System Board |
| Check Printer before | |
| replacing system board | |
| 15XX | 1. SDLC Adapter |
| 1692 | 1. Run FDISK to ensure at least one |
| Boot sequence error | active partition is set active |
| 16XX | 1. 36/38 Workstation Adapter |
| 1762 | 1. Run Configuration |
| Hard disk drive configuration error | See 'Setup Utility Program' |
| 1780 1790 (Disk Drive 0) | 1. Power Supply ('Voltage check') |
| 1781 1791 (Disk Drive 1) | 2. Hard Disk Drive |
| 1782 1792 (Disk/CD-ROM Drive 2) | 3. Hard Disk Drive |
| 1783 1793 (Disk/CD-ROM Drive 3) | 4. System Board |
| 5. Hard Disk Cable | |
| 6. Power Supply | |
| 17XX | 1. Hard Disk Drive Jumpers |
| 2. Hard Disk Drive connection/cable | |
| 3. Hard Disk Drive | |
| 4. System Board | |
| 5. Power Supply | |
| 1800 | |
| PCI Error (IRQ not available) | 2. Failing Adapter |
| 3. System Board | |
| 1801 | |
| (No room for PCI option ROM) | 2. Failing Adapter |
| 3. System Board | |
| 1802 | |
| (No more I/O address space | 2. Failing Adapter |
| available for PCI adapter) | 3. System Board |
| 1803 | |
| (No more memory (above | 2. Failing Adapter |
| 1MB) for PCI adapter) | 3. System Board |
| 1804 | |
| (No more memory (below | 2. Failing Adapter |
| 1MB) for PCI adapter) | 3. System Board |
| 1805 | 1. Remove Failing PCI Card |
| (PCI option ROM checksum | 2. System Board |
| error) | |
| 180X 185X | 1. Run Setup and verify PCI/ISA |
| (PCI configuration or | configuration settings. |
| resource error) | 2. If necessary, set ISA adapters to 'Not available' |
| to allow PCI adapters to properly configure | |
| 3. Remove any suspect ISA adapters | |
| 4. Rerun diagnostics | |
| 5. PCI Adapter | |
| 6. PCI Riser Card | |
| 1962 | 1. Run Configuration Setup |
| (No valid boot device found | 2. Run Diagnostics |
| be sure the drive you want | 3. Drive Cable |
| to start from is the boot | 4. Hard Disk Drive |
| sequence) | 5. System Board |
| See 'Hard Disk Drive Boot Error' | |
| 1996 | 1. Run Configuration Setup |
| Boot Sequence Error | |
| 209X | 1. Diskette Drive |
| 2. Diskette Cable | |
| 3. 16-Bit AT Fast SCSI Adapter | |
| 20XX | 1. BSC Adapter |
| Not listed above | 2. Riser Card |
| 21XX | 1. SCSI Device |
| 2. 16-Bit AT Fast SCSI Adapter | |
| 3. Alternate BSC Adapter | |
| 4. Riser Card | |
| 2401 2402 | 1. Display |
| If screen colors change | |
| 2401 2402 | 1. System Board |
| If screen colors are OK | 2. Display |
| 2408 | 1. System Board |
| 2409 | 1. Display |
| 2410 | 1. System Board |
| 2. Display | |
| 2462 | 1. Check Cable connections |
| Video memory configuration error | 2 Run Setup and verify video config. |
| 3. Video Memory Modules | |
| 4. Video Adapter (if installed) | |
| 5. System Board | |
| 3015 3040 | 1. Network Attached ? |
| Check for missing wrap | 2. LF Translator |
| or terminator plug on the | 3. Cable Problem |
| adapter | 4. PC Network Adapter |
| 5. Riser Card | |
| 30XX | 1. PC Network Adapter |
| 2. LF Translator | |
| 3. Cable Problem ? | |
| 4. Riser Card | |
| 3115 3140 | 1. Network Attached ? |
| 2. LF Translator | |
| 3. Alternate PC Network-Adapter | |
| 4. Cable Problem | |
| 5. Riser Card | |
| 31XX | 1. Alternate PC Network Adapter |
| 2. LF Translator | |
| 3. Cable Problem ? | |
| 4. Riser Card | |
| 36XX | 1. GPIB Adapter |
| 2. Riser Card | |
| 38XX | 1. DAC Adapter |
| 2. Riser Card | |
| 4611 4630 | 1. Multiport/2 Interface Board |
| 2. Multiport/2 Adapter | |
| 4612 4613 4640 4641 | 1. Memory Module Package |
| 2. Multiport/2 Adapter | |
| 4650 | 1. Multiport Interface Cable |
| 46XX | 1. Multiport/2 Adapter |
| Not listed above | 2. Multiport/2 Interface Board |
| 3. Memory Module | |
| 5600 | 1. Financial System Controller Adapter |
| 5962 | 1. Run Configuration |
| An IDE device (other than | 2. CD-ROM Drive |
| hard drive) configuration | 3. CD-ROM Adapter |
| error. | 4. ZIP or other ATAPI device |
| 5. System Board | |
| 62XX | 1. 1st Store Loop Adapter |
| 2. Adapter Cable | |
| 63XX | 1. 2nd Store Loop Adapter |
| 2. Adapter Cable | |
| 64XX | 1. Network Adapter |
| 71XX | 1. Voice Adapter |
| 74XX | 1. Video Adapter (if installed) |
| 2. Riser Card | |
| 76XX | 1. Page Printer Adapter |
| 78XX | 1. High Speed Adapter |
| 79XX | 1. 3117 Adapter |
| 80XX | 1. PCMCIA Adapter |
| 84XX | 1. Speech Adapter |
| 2. Speech Control Assembly | |
| 3. Riser Card | |
| 8601 8602 | 1. Pointing Device (Mouse) |
| 2. System Board | |
| 8603 8604 | 1. System Board |
| 2. Pointing Device (Mouse) | |
| 86XX | 1. Mouse |
| Not listed above | 2. System Board |
| 89XX | 1. PC Music Adapter |
| 2. MIDI Adapter Unit | |
| 3. Riser Card | |
| 91XX | 1. Optical Drive |
| 2. Adapter | |
| 96XX | 1. SCSI Adapter |
| 2. Any SCSI Device | |
| 3. System Board | |
| 10101 10102 10104 | 1. Have customer verify correct |
| 10105 10106 10107 | operating system device |
| 10108 10109 10111 | drivers are installed and operational |
| 10112 10113 10114 | 2. Modem |
| 10115 10116 | |
| 10103 10110 101171 | 1. System Board |
| 2. Data/Fax Modem | |
| 10117 | 1. Check System Speaker |
| Not listed above | 2. Check PSTN cable |
| 3. External DAA (if installed) | |
| 4. Modem | |
| 10118 | 1. Run Diagnostics and verify |
| the correct operation of the | |
| modem slot | |
| 2. Modem | |
| 10119 | 1. Diagnostics detected a non-IBM modem |
| 2. Modem | |
| 10120 | 1. Check PSTN Cable |
| 2. External DAA (if installed) | |
| 3. Modem | |
| 10132 10133 10134 | 1. Modem |
| 10135 10136 10137 | |
| 10138 10139 10140 | |
| 10141 10142 10143 | |
| 10144 10145 10146 | |
| 10147 10148 10149 | |
| 10150 10151 10152 | |
| 10153 | 1. Data/Fax Modem |
| 2. System Board | |
| 101XX | 1. Modem Adapter/A |
| Not listed above | 2. Data/Fax Modem |
| 3. Riser Card | |
| 4. System Board | |
| 10450 10451 10490 | 1. Run Advanced Diagnostics |
| 10491 10492 10499 | 2. Riser Card |
| Read/write error | 3. Hard Disk Drive |
| 4. System Bord | |
| 10452 | 1. Run Advanced Diagnostics |
| Seek test error | |
| 10453 | Information only |
| Wrong drive type ? | |
| 10454 | 1. Run Advanced Diagnostics |
| Sector buffer test error | |
| 10455 10456 | 1. Run Advanced Diagnostics |
| Controller error | |
| 10459 | Information only |
| Drive diagnostic command error | |
| 10461 | 1. Run Advanced Diagnostics |
| Drive format error | |
| 10462 | 1. Run Advanced Diagnostics |
| Controller seek error | |
| 10464 | 1. Run Advanced Diagnostics |
| Hard Drive read error | |
| 10467 | 1. Run Advanced Diagnostics |
| Drive non fatal seek error | |
| 10468 | 1. Run Advanced Diagnostics |
| Drive fatal seek error | |
| 10469 | 1. Run Advanced Diagnostics |
| Drive soft error count exceeded | |
| 10470 10471 10472 | 1. Run Advanced Diagnostics |
| Controller wrap error | |
| 10473 | Information only |
| Corrupt data, Low level | |
| format might be required | |
| 10480 | 1. Hard Disk Drive (ESDI) |
| 2. Drive Cable | |
| 3. System Board | |
| 10481 | 1. Run Advanced Diagnostics |
| ESDI drive D seek error | |
| 10482 | 1. Run Advanced Diagnostics |
| Drive select acknowledgement bad. | |
| 106X1 | 1. Check Configuration |
| 2. Ethernet Adapter | |
| 10635 | 1. Power-off computer, wait ten seconds, |
| then power-on the computer | |
| 2. Ethernet Adapter | |
| 10651 10660 | 1. Check Cables |
| 2. Ethernet Adapter | |
| 106XX | 1. Ethernet Adapter |
| Not listed above | |
| 107XX | 1. 5.25-Inch External Diskette Drive |
| 2. 5.25-Inch Diskette Drive Adapter/A | |
| 109XX | 1. ActionMedia Adapter/A |
| Check the adapter cables | 2. System Board |
| 112XX | 1. SCSI Adapter |
| This adapter does not have cache | 2. Any SCSI Device |
| 3. System Board | |
| 119XX | 1. 3119 Adapter |
| 121XX | 1. Modem Adapter |
| 2. Any Serial Device | |
| 3. System Board | |
| 136XX | 1. ISDN Primary Rate Adapter |
| 2. System Board | |
| 137XX | 1. System Board |
| 141XX | 1. Realtime Interface Coprocessor |
| Portmaster Adapter/A | |
| 143XX | 1. Japanese Display Adapter |
| 2. System Board | |
| 14710 14711 | 1. System Board Display Adapter |
| 2. Adapter Video Memory | |
| 148XX | 1. Display Adapter |
| 14901 14902 | 1. Display Adapter (if installed) |
| 1491X 14922 | 2. System Board |
| 3. Display (any type) | |
| 14932 | 1. External Display |
| 2. Display Adapter | |
| 16101 | 1. Riser card Battery |
| 161XX | 1. FaxConcentrator Adapter |
| 164XX | 1. 120MB Internal Tape Drive |
| 2. Diskette Cable | |
| 3. System Board | |
| 16500 | 1. 6157 Tape Attachment Adapter |
| 16520 16540 | 1. 6157 Streaming Tape Drive |
| 2. 6157 Tape Attachment Adapter | |
| 166XX 167XX | 1. Token Ring Adapter |
| 2. System Board | |
| 3. Riser Card | |
| 18001 to 18029 | 1. Wizard Adapter |
| 2. Wizard Adapter Memory | |
| 18031 to 18039 | 1. Wizard Adapter Cable |
| 185XXXX | 1. DBCS Japanese Display Adapter/A |
| 2. System Board | |
| 20001 to 20003 | 1. Image (Image-I) Adapter/A |
| 2. Memory Module DRAM, VRAM | |
| 20004 | 1. Memory Module DRAM, VRAM |
| 2. Image (Image-I) Adapter/A | |
| 20005 to 20010 | 1. Image (Image-I) Adapter/A |
| 2. Memory Module DRAM, VRAM | |
| 200XX | 1. Image (Image-I) Adapter/A |
| 2. Memory Module DRAM, VRAM | |
| 3. System Board | |
| 20101 to 20103 | 1. Printer/Scanner Option |
| 2. Image Adapter/A | |
| 3. Memory Module DRAM, VRAM | |
| 20104 | 1. Memory Module DRAM, VRAM |
| 2. Printer/Scanner Option | |
| 3. Image Adapter/A | |
| 20105 to 20110 | 1. Printer/Scanner Option |
| 2. Image Adapter/A | |
| 3. Memory Module DRAM, VRAM | |
| Image Adapter/A | 1. Replace memory module |
| Memory Test failure indicated | ('shown in graphic') |
| by graphic of adapter | |
| 206XX | 1. SCSI-2 Adapter |
| 2. Any SCSI Device | |
| 3. System Board | |
| 208XX | 1. Any SCSI Device |
| Verify there are no duplicate | |
| SCSI ID settings on the same bus | |
| 210XXXX | 1. SCSI Hard Disk Drive |
| Internal bus, size unknown | 2. SCSI Adapter or System Board |
| 210XXX1 | 3. SCSI Cable |
| External bus, size unknown | 4. SCSI ID Switch (on some models) |
| Tape Drive amber LED | 1. Tape Drive |
| remains on | 2. SCSI Cable (internal) |
| 3. SCSI Adapter or System Board | |
| Tape Drive green 'in use' | 1. Tape Drive |
| LED fails to come on | 2. SCSI Adapter or System Board |
| 3. SCSI Cable (internal) | |
| SCSI Cable (external) | |
| Tape automatically ejected | 1. Tape Cassette |
| from drive | 2. Drive |
| SCSI ID on rotary switch does | 1. Rotary Switch Circuit Board |
| not match SCSI ID set in | 2. Circuit Board Cable |
| configuration | 3. Tape Drive |
| Verify drive switches inside | |
| cover are set to zero | |
| Tape sticks/breaks in drive | 1. Tape Cassette |
| Verify that the tapes used | |
| meet ANSI standard X3B5 | |
| 212XX | 1. SCSI Printer |
| 2. Printer Cable | |
| 213XX | 1. SCSI Processor |
| 214XX | 1. WORM Drive |
| 215XXXC | 1. CD-ROM Drive I |
| 215XXXD | CD-ROM Drive II |
| 215XXXE | Enhanced CD-ROM Drive II |
| 215XXXU | Any CD-ROM Drive II |
| If an external device, and | 2. SCSI Cable |
| power-on LED is off, check | 3. SCSI Adapter or System Board |
| external voltages. | |
| 216XX | 1. Scanner |
| 217XX | 1. Rewritable Optical Drive |
| If an external device, and | 2. SCSI Adapter or System Board |
| power-on LED is off, check | 3. SCSI Cable |
| external voltages | |
| 218XX | 1. Changer |
| Check for multi CD tray, or | |
| juke box | |
| 219XX | 1. SCSI Communications Device |
| 24201Y0 24210Y0 | 1. ISDN/2 Adapter |
| Be sure wrap plug is attached | 2. ISDN Wrap Plug |
| 3. ISDN/2 Communications Cable | |
| 273XX | 1. 1 Mbps Micro Channel |
| Infrared LAN Adapter | |
| 27501 27503 | 1. ServerGuard Adapter |
| 27506 27507 | 2. System Board |
| 27502 27504 27510 | 1. ServerGuard Adapter |
| 27511 27533 27534 | |
| 27536 27537 | |
| 27509 | 1. Remove redundant adapters, |
| run Auto Configuration program | |
| then retest | |
| 27512 | 1. WMSELF.DGS diagnostics |
| file missing | |
| 2. WMSELF.DGS diagnostics | |
| file incorrect | |
| 27535 | 1. 3V Lithium Backup Battery |
| 2. ServerGuard Adapter | |
| 27554 | 1. Internal Temperature out of range |
| 2. ServerGuard Adapter | |
| 27555 27556 | 1. ServerGuard Adapter |
| 2. Power Supply | |
| 27557 | 1. 7.2V NiCad Main Battery Pack |
| 2. ServerGuard Adapter | |
| 27558 27559 | 1. PCMCIA Type II Modem |
| 27560 27561 | 2. ServerGuard Adapter |
| 27562 | 1. External Power Control not connected |
| 2. External Power Control | |
| 3. ServerGuard Adapter | |
| 27563 27564 | 1. External Power Control |
| 2. ServerGuard Adapter | |
| 275XX | 1. Update Diagnostic Software |
| 27801 to 27879 | 1. Personal Dictation System Adapter |
| 2. System Board | |
| 27880 to 27889 | 1. External FRU (Speaker, Microphone) |
| I999030X | 1. Possible hard disk drive problem |
| (Hard disk reset failure) | See 'Hard Disk Drive Boot Error' |
| (Boot error) | |
| (No operating system installed) |
Please see the LEGAL - Trademark notice.
Feel free - send a 
for any BUG on this page found - Thank you.