|
|
|
| BIOS Error Codes, Messages | Action/FRU |
|---|---|
| 0111 | ISA adapter card |
| I/O Parity Error | System board |
| 0127 | Check CPU speed and system board DIP switches. |
| CPU Clock Mismatch | |
| See 'System Board Jumpers and Connectors' | |
| for 'Machine Type 2139' | |
| for 'Machine Type 2153/K6' | |
| for 'Machine Type 2153/Celeron™' | |
| --- | for 'Machine Type 2158' |
| for 'Machine Type 2163'. | |
| System board | |
| 0151 | Enter BIOS Setup and load the default settings. |
| Real Time Clock Error | CMOS battery. |
| 0161 | System board. |
| CMOS Battery Bad | |
| 0162 | |
| CMOS Checksum Error | |
| 0162 | Ensure the system configuration set in BIOS Setup is correct. |
| Equipment Configuration Error | See 'BIOS Setup Utility' |
| Enter BIOS Setup and load the default settings. | |
| CMOS battery. | |
| System board. | |
| 0163 | Ensure the time set in BIOS Setup is correct. |
| Date and Time Incorrect | See 'Date and Time' |
| CMOS battery. | |
| 0164 | Insert the memory modules in the DIMM sockets properly, |
| Memory Size Change | then reboot the system. |
| 0201 | Memory module. |
| Memory Error at MMMM:SSSS:OOOOh | See the 'Step 005' of 'Memory' to replace memory module. |
| System board. | |
| 301 | Re-connect PS/2 keyboard and mouse. |
| PS/2 Keyboard Error or | Enter BIOS Setup and load the default settings. |
| Keyboard Not Connected | PS/2 keyboard |
| 303 | PS/2 mouse |
| PS/2 Keyboard Interface Error | System board |
| 0662 | |
| Onboard Floppy Drive I/O Address | |
| Conflict(s) | |
| 0662 | |
| Onboard Floppy Drive DMA Conflict(s) | |
| 0662 | |
| Onboard Floppy Drive IRQ Conflict(s) | Enter BIOS Setup and load the default settings. |
| Remove all adapter cards that are NOT factory-installed, | |
| then reboot the system. | |
| 0662 | Diskette drive cable/connection. |
| Floppy Disk Controller Error | Diskette drive. |
| 0662 | System board |
| Floppy Drive A Error | |
| 0662 | |
| Floppy Drive B Error | |
| 0648 | Ensure that the diskette drive is not set to [Write Protected] |
| Floppy Drive(s) Write Protected | in the Security Options in BIOS Setup. |
| Load default settings in Setup. | |
| 0962 | Enter BIOS Setup and load the default settings. |
| Onboard Parallel Port | Remove all adapter cards that are NOT factory-installed, |
| Conflict(s) | then reboot the system. |
| 0962 | |
| Onboard Parallel Port I/O | |
| Address Conflict(s) | |
| 0962 | |
| Onboard Parallel Port | |
| IRQ Conflict(s) | |
| 0962 | |
| Onboard ECP Parallel Port | |
| DMA Conflict(s) | |
| 1162 | |
| Onboard Serial Port | |
| Conflict(s) | |
| 1162 | |
| Onboard Serial Port I/O | |
| Address Conflict(s) | |
| 1162 | |
| Onboard Serial Port IRQ Conflict(s) | |
| 1755 | Ensure that the hard disk drive is not set |
| Hard Disk Drive(s) Write Protected | to [Write Protected] in the |
| Security Options in BIOS Setup. | |
| Load default settings in Setup. | |
| 1762 | Enter BIOS Setup and load the default settings. |
| Onboard IDE Primary Channel I/O | Remove all adapter cards that are NOT factory-installed, |
| Address Conflict(s) | then reboot the system. |
| 1762 | |
| Onboard IDE Primary Channel IRQ | |
| Conflict(s) | |
| 1762 | |
| Onboard IDE Secondary Channel I/O | |
| Address Conflict(s) | |
| 1762 | |
| Onboard IDE Secondary Channel IRQ | |
| Conflict(s) | |
| 1780 | Enter BIOS Setup and load the default settings. |
| IDE Primary Channel Master Drive Error | Check IDE drive jumper. |
| 1781 | See '3.5-In. Hard Disk Drive Jumper Settings' and |
| IDE Primary Channel Slave Drive Error | '5.25-In. Hard Disk Drive Jumper Settings'. |
| 1782 | IDE hard disk drive power. |
| IDE Secondary Channel Master Drive Error | IDE hard disk drive cable/connection. |
| 1783 | IDE hard disk drive. |
| IDE Secondary Channel Slave Drive Error | |
| 1780 | Enter BIOS Setup and load the default settings. |
| IDE Primary Channel Master Drive | IDE hard disk drive cable/connection. |
| Changed | |
| 1781 | |
| IDE Primary Channel Slave Drive | |
| Changed | |
| 1782 | |
| IDE Secondary Channel Master Drive | |
| Changed | |
| 1783 | |
| IDE Secondary Channel Slave Drive | |
| Changed | |
| 1800 | Load default settings in Setup. |
| IRQ Setting (PnP ISA Card(s) disabled) | Enter BIOS Setup and set the Reset Resource |
| 1801 | Assignments parameter to Yes, then |
| Expansion ROM Allocation Failed | reboot the system. See 'PnP/PCI Options'. |
| 1802 | Remove all adapter cards that are NOT factory-installed, |
| I/O Resource Conflict(s) | then reboot the system |
| 1803 | |
| Memory Resource Conflict(s) | |
| 1800 | Do not have enough system resource allowed to |
| PnP ISA Card(s) Disabled | allocate for ISA adapter card. |
| Remove the ISA adapter card. | |
| Load default settings in Setup. | |
| Enter BIOS Setup and set the | |
| Reset Resource Assignments parameter to Yes, | |
| then reboot the system. | |
| See 'PnP/PCI Options'. | |
| Remove all adapter cards that are NOT | |
| factory-installed, then reboot the system | |
| 8601 | PS/2 Pointing Device Error or Not Connected |
| PS/2 Pointing Device Interface Error | Re-connect PS/2 keyboard and mouse. |
| 8603 | Enter BIOS Setup and load the default settings. |
| PS/2 Pointing Device Error | PS/2 mouse |
| 8603 | PS/2 keyboard |
| System board | |
| 8602 | Enter BIOS Setup and load the default settings. |
| Onboard Pointing IRQ Device Conflict(s) | Remove all adapter cards that are NOT |
| factory-installed, then reboot the system. |
Please see the LEGAL - Trademark notice.
Feel free - send a 
for any BUG on this page found - Thank you.