Return to MAIN-Index  Return to SUB-Index    IBM-AUSTRIA - PC-HW-Support    30 Aug 1999

Numeric Error Codes 701C, 701CS (2630)



Numeric Error Codes 701C, 701CS (2630)

Numeric error codes show the errors detected in POST or system operation. Use the error codes displayed on the screen to diagnose failures. If more than one error code is displayed, begin the diagnosis with the first error code. The cause of the first error code can result in false error codes being displayed.

In the following error codes, X can be any number.

Symptom/Error    FRU/Action
  
02X, 101, 107 1. Battery
  2. AC Adapter
  3. Memory Option
  4. Top System Board
  
10X 1. Bottom System Board
  
119 1. Top System Board.
  
161, 163 1. Set Configuration
      (Press Fn+F1 to enter the
      Configuration Utility and set
      the time and date.)
  2. Top System Board.
  3. Bottom System Board.
  
162 1. Set Configuration.
(Check the Installed Devices     (Press Fn+F1 to enter the
list for a missing device.)     Configuration Utility and set
      your configuration.)
  2. Any Missing Device.
  3. Top System Board.
  4. Bottom System Board.
  
164 1. If a SO-DIMM card has been removed,
(Memory size error)     press Fn+F1 to enter the Configuration
      Utility, and verify the memory size.
  2. Replace the installed SO-DIMM.
  3. Bottom System Board.
  
184 1. Press Fn+F1 to enter the Configuration
      Utility, and then reset the Power-on Password
  
195 1. Check if the disk drive is from another
(The hibernate partition does     computer or if the memory size has changed.
not match memory size.) 2. Go to 'Hard Disk Drive Checkout'
  3. Hard Disk Drive
  
196 1. Disable, and then enable Hibernate mode.
(Read error occurred in the 2. Go to 'Hard Disk Drive Checkout'
hibernate area of the 3. Hard Disk Drive
Hard Disk Drive.)
197 1. Disable, and then enable Hibernate mode.
(The computer memory size is
not equal to the hibernate
area size on the Hard Disk
Drive.)
1XX 1. Top System Board.
(Not listed above.) 2. Bottom System Board.
  
2XX 1. Go to 'Memory Checkout'
  2. SO-DIMM
  3. Bottom System Board
  
3XX 1. Remove attached external devices.
(Before replacing FRUs, power-off, 2. Reseat cables.
and then power-on the computer.) 3. Keyboard
  4. Top System Board
  
6XX 1. Go to 'Diskette Drive Checkout'
  2. Diskette
  3. Diskette Drive Cable
  4. Diskette Drive
  5. Top System Board
  
09XX, 10XX 1. Top System Board.
  
11XX 1. Modem
  2. Top System Board
  3. Bottom System Board
  
17XX 1. Go to 'Hard Disk Drive Checkout'
  2. Hard Disk Drive
  3. Bottom System Board
  
24XX 1. External Display.
(For external displays, see the 2. External Display Power Cord.
'External Display Self-Test' in the 3. Backlight Lamp Assembly.
'Common Devices Checkout section' 4. LCD Assembly.
before replacing any FRUs.) 5. Bottom System Board.
  6. Inverter Card.
  
8000 1. Set Configuration.
  2. PCMCIA Card.
  3. Bottom System Board.
  
860X 1. External Mouse.
(Pointing device error when 2. External Keyboard.
TrackPoint III is disabled.) 3. Top System Board
  4. Bottom System Board
  
861X 1. Reseat the TrackPoint III cable
(Pointing device error when     (the narrowest keyboard cable)
(TrackPoint III is enabled.)     at the Top System Board.
  2. External Mouse
  3. Keyboard
  4. Top System Board
  5. Bottom System Board
  
86XX 1. Pointing Device.
(Not listed above) 2. TrackPoint III.
  3. Keyboard.
  4. Numeric Keypad.
  5. Top System Board.
  6. Bottom System Board.
  
12902 1. Bottom System Board.
  
I9990305 1. Go to 'Hard Disk Drive Checkout'
  2. Hard Disk Drive
  3. Bottom System Board
  
Other codes not 1. Go to 'Undetermined Problems'
listed above


More INFORMATION / HELP is available at the  IBM-HelpCenter

Please see the LEGAL  -  Trademark notice.
Feel free - send a Email-NOTE  for any BUG on this page found - Thank you.