The Manual-Adjust Menu (9516-Bxx)

^{IBM-AUSTRIA - PC-HW-Support 30 Aug 1999}

The Manual-Adjust Menu (9516-Bxx)

The Manual-Adjust Menu

You can run the following functions from the manual-adjust menu:

Decreasing the noise, such as the noise on the screen
Adjusting the hue
Adjusting the display position and size on the screen

If the message "Quit without saving?" is displayed

The message "Quit without saving?" is displayed if you specify the settings in the manual-adjust menu and try to exit the menu. Select SAVE VALUES to store the values and exit, or select Quit to exit without saving them.

Function    Explanation

PHASE:    When there are visual noises on the edges of characters and graphics,

   adjust this parameter to suppress the noise. You can set values from 0 to 23.

CLOCK:    Adjust this parameter to suppress the display of vertical stripes.

   (This parameter adjusts the frequency of the sampling analog video signal

   from your PC.)

SHARP:    Adjust to eliminate some of the high frequency composition in the video signal.

   You can set values from 0 to 255. (Do not set this normally.)

RED:    Adjust this parameter to change the red hue level of the screen.

   You can set values from 0 to 255.

GREEN:    Adjust this parameter to change the green hue level of the screen.

   You can set values from 0 to 255.

BLUE:    Adjust this parameter to change the blue hue level of the screen.

   You can set values from 0 to 255.

OFFSET R:    When there are red noises on the black part of the screen, adjust this

   parameter to suppress it. You can set values from 0 to 255.

OFFSET G:    When there are green noises on the black part of the screen, adjust this

   parameter to suppress it. You can set values from 0 to 255.

OFFSET B:    When there are blue noises on the black part of the screen, adjust this

   parameter to suppress it. You can set values from 0 to 255.

H-POSI:    Adjust this parameter to change the horizontal position of the screen.

   The values you can set depend on your PC.

V-POSI:    Adjust this parameter to change the vertical position of the screen.

   The values you can set depend on your PC.

H-SIZE:    If the screen resolution is less than 1280x1024

   (the resolution of the monitor), adjust the horizontal size.

   The value you can set varies with the resolution.

V-SIZE:    If the screen resolution is less than 1280x1024

   (the resolution of the monitor), adjust the vertical size.

   The value you can set varies with the resolution.

SAVE VALUES:    Use this parameter to store the values you set in the manual-adjust menu.

   Otherwise, the values you set are erased when you exit the menu.

LOAD DEFAULT VALUES:    Use this parameter to restore all the values in the manual-adjust menu

   to the settings of auto setup. (If auto setup was not performed, the values

   are restored to the original settings when the monitor was shipped.)

System Reset:    Use this parameter to restore all the values to the original settings

   when the monitor was shipped.

Function	Explanation

PHASE:	When there are visual noises on the edges of characters and graphics,
	adjust this parameter to suppress the noise. You can set values from 0 to 23.

CLOCK:	Adjust this parameter to suppress the display of vertical stripes.
	(This parameter adjusts the frequency of the sampling analog video signal
	from your PC.)

SHARP:	Adjust to eliminate some of the high frequency composition in the video signal.
	You can set values from 0 to 255. (Do not set this normally.)

RED:	Adjust this parameter to change the red hue level of the screen.
	You can set values from 0 to 255.

GREEN:	Adjust this parameter to change the green hue level of the screen.
	You can set values from 0 to 255.

BLUE:	Adjust this parameter to change the blue hue level of the screen.
	You can set values from 0 to 255.

OFFSET R:	When there are red noises on the black part of the screen, adjust this
	parameter to suppress it. You can set values from 0 to 255.

OFFSET G:	When there are green noises on the black part of the screen, adjust this
	parameter to suppress it. You can set values from 0 to 255.

OFFSET B:	When there are blue noises on the black part of the screen, adjust this
	parameter to suppress it. You can set values from 0 to 255.

H-POSI:	Adjust this parameter to change the horizontal position of the screen.
	The values you can set depend on your PC.

V-POSI:	Adjust this parameter to change the vertical position of the screen.
	The values you can set depend on your PC.

H-SIZE:	If the screen resolution is less than 1280x1024
	(the resolution of the monitor), adjust the horizontal size.
	The value you can set varies with the resolution.

V-SIZE:	If the screen resolution is less than 1280x1024
	(the resolution of the monitor), adjust the vertical size.
	The value you can set varies with the resolution.

SAVE VALUES:	Use this parameter to store the values you set in the manual-adjust menu.
	Otherwise, the values you set are erased when you exit the menu.

LOAD DEFAULT VALUES:	Use this parameter to restore all the values in the manual-adjust menu
	to the settings of auto setup. (If auto setup was not performed, the values
	are restored to the original settings when the monitor was shipped.)

System Reset:	Use this parameter to restore all the values to the original settings
	when the monitor was shipped.

More INFORMATION / HELP is available at the IBM-HelpCenter

Please see the LEGAL - Trademark notice.
Feel free - send a for any BUG on this page found - Thank you.