|
|
|
ERROR - Codes valid for all PS/2 (MC) Models
| Symptom/Error: | FRU/Action. |
|---|---|
| 000101XX | 1. Run Advanced Diagnostics |
| (Interrupt failure. Possibly a | 2. 486DX33 Upgrade (70/80) |
| bad battery or processor) | |
| 000102XX | 1. Run Advanced Diagnostics |
| (ROM checksum or timer error. Possibly | 2. 486DX33 Upgrade (70/80) |
| a bad battery or processor) | |
| (If the battery was removed while replacing | |
| the 80386 processor in a model 70, with a | |
| 486DX33 Processor Upgrade (FRU Number | |
| 92F0436), remove the 486DX33 processor | |
| and install the 80386 processor, then | |
| install the battery. Configure the system | |
| and re-install the 486DX33 processor | |
| without removing the battery.) | |
| 00010300 | 1. Processor Board (90/95) |
| (Checksum or timer error. If it is a | 2. System Board |
| 20 MHz board, and the processor is not a | |
| 487SX, the jumper must be | |
| in positions 2 and 3) | |
| (487SX is indicated on the processor) | |
| 000102XX 000103XX | 1. System Board |
| 000104XX 000107XX | 2. Processor Board |
| 000105XX | (Information only) |
| (Command not accepted) | |
| 000106XX | 1. Run Advanced Diagnostics |
| (Converting logic test failure) | |
| 000107XX 000108XX | 1. System Board Memory |
| 000109XX | 2. System Board |
| (Interrupt or memory failure) | 3. Processor Board (90/95) |
| 4. Any Adapter | |
| 5. Bus Adapter | |
| 00010XXX | 1. System Board |
| 000110XX | 1. Memory Module Kit |
| (Check Memory) (For Model 95, also | 2. System Board |
| see 000201XY for socket location list) | |
| 000111 | 1. Adapter Memory |
| I/O channel check | 2. Expansion Adapter |
| 3. System Board | |
| 000112XX 000113XX | 1. System Board |
| (Possible MC-timeout error) | 2. Processor Board (90/95) |
| 000114XX | 1. Any Adapter |
| (ROM error) | 2. Bus Adapter |
| 000115XX | 1. System Board |
| (80386 protected mode failure, or BIOS | 2. 486DX33 Upgrade (70/80) |
| checksum error) | |
| 000116XX | 1. Run Advanced Diagnostics |
| (Possible read/write problem) | 2. 486DX33 Upgrade (70/80) |
| 000118XX | 1. System Board Memory |
| (Previously detected error. | 2. Processor Board (90/95) |
| Run Advanced Diagnostics) | |
| 000119XX | 1. Run Automatic Configuration |
| (2.88MB diskette drive is | |
| installed but not supported.) | |
| 2. System Board | |
| 00011XXX | 1. System Board |
| (not listed above) | |
| 000120XX | 1. System Board Processor Cache |
| Possible Processor self test failure) | (90/95) |
| 2. Processor Board | |
| (90/95) | |
| 000121XX | (Information only) |
| (A problem was detected during | |
| memory remapping (256KB ROM Error)) | |
| 000122XX | 1. Run Advanced Diagnostics |
| (POST found a hardware error) | |
| 00012201 00012202 | 1. Run Advanced Diagnostics |
| 00012203 00012204 | |
| 00012205 00012206 | |
| 00012207 00012208 | |
| (Data error, Possible system board | |
| failure) | |
| 000129XX | 1. Run Advanced Diagnostics |
| 2. Cache Kit | |
| 3. System Board | |
| 000130XX | 1. Check Drive Sequence |
| (POST could not start the operating | |
| system. Operating system loaded ? Is | |
| the boot drive in the selectable drive | |
| sequence ? | |
| 00013001 | 1. Delete diskette drive from |
| (Security system is being used, but the | the startup sequence if so |
| computer is not totally secured because | desired. |
| there is a diskette drive in the | |
| startup sequence) | |
| 00013002 | 1. Run Automatic Configuration |
| (Drive startup sequence is corrupt | then reset the selectable drive |
| or invalid) | startup sequence. If the problem |
| still exists, replace the | |
| system board | |
| 00013003 | 1. Run Automatic Configuration |
| (EEPROM could not be read) | If the problem still exits, replace |
| the system board. | |
| 000131XX | 1. System Board |
| 000132XX | 1. Run Advanced Diagnostics |
| (DMA extended registers error) | |
| 000133XX | 1. Run Advanced Diagnostics |
| (DMA verify function error. Logic failed.) | |
| 000134XX | 1. Run Advanced Diagnostics |
| (DMA arbitration logic error.) | |
| 00014905 | 1. System Board |
| 2. Processor Board | |
| 00014908 00014909 | 1. System Board |
| Before replacing any FRUs, see | 2. Tamper Evident Switches |
| 'Cover Lock and Tamper-Evident Switches' | 3. Keylock Assembly |
| 000152XX | 1. Run Advanced Diagnostics |
| (Real time clock error. (This is not | |
| always a hardware failure. See also | |
| 'Real-Time Clock Problems' | |
| 000156XX | 1. Start the system from the |
| (Security error. The covers were | Reference diskette (or server |
| removed without using the key. The | image) and reconfigure the system. |
| tamper evident switch was tripped.) | 2. Security Switch Assembly |
| 3. System Board | |
| 000160XX | 1. Run Advanced Diagnostics |
| (System Board ID not recognized. | |
| Possible system board failure) | |
| 000161XX | 1. Battery |
| CAUTION: | 2. Processor Board (90/95) |
| The lithium battery (IBM part number | 3. System Board |
| 33F8354) in your computer presents | 4. Bus Adapter |
| a fire, explosion, or severe burn risk. | |
| Use of another battery could result in | |
| ignition or explosion of the battery. | |
| 000162XX | 1. Any Device |
| (Be sure all devices are powered-on. | 2. Battery |
| (Check Enable/Disable settings) | |
| Configuration changed ? If so, run | |
| Automatic Configuration. | |
| 000163XX | 1. Set Date and Time |
| (Date and time error) | |
| 00016000 00016400 | 1. Set Configuration, Features |
| 00016500 00016700 | 2. System Board |
| 00016900 | |
| (If setting configuration, date and time | |
| does not solve the problem, see | |
| Devices List' | |
| 000166XX | 1. Run Advanced Diagnostics |
| (Adapter-busy. Reseat all adapters) | |
| 000167XX | 1. Set Features. Set date and time |
| (Clock is not working correctly.) | |
| 000168XX | 1. Run Advanced Diagnostics |
| (Real time clock error. this is not always | |
| a hardware failure. also see | |
| 'Real-Time Clock Problems.) | |
| 000169XX | 1. Processor Board |
| Processor configuration error. (Run Automatic | 2. System Board |
| Configuration, then verify that the processor | |
| configuration information is correct before | |
| replacing FRUs) | |
| 000170XX | 1. From Set Configuration, select |
| (ASCII console setup conflict error. | Change Configuration, and enable |
| The serial port is disabled) | the port |
| 000171XX | 1. Battery |
| 2. Processor Board (90/95) | |
| 3. System Board | |
| 4. Bus Adapter | |
| 000172XX | 1. System Board |
| 000173XX | 1. Set Configuration/Features |
| (Possibly a weak battery) | |
| 000174XX | 1. Any Device |
| (If the configuration has been changed, | 2. System Board |
| run Automatic Configuration. Otherwise | 3. Bus Adapter |
| run Advanced Diagnostics) | |
| (Check 'SCSI Device Default Settings' | |
| 000175XX | 1. System Board |
| (Security error. The system board EEPROM | |
| failed) | |
| 000176XX | 1. Start the system from the |
| (Security error. The covers were removed | Reference Diskette (or server |
| without using the key. The tamper evident | image) and reconfigure the |
| switch was tripped) | system. |
| 2. Security Switch Assembly | |
| 3. System Board | |
| 000177XX 000178XX | 1. System Board |
| Security error. Passwords corrupted) Reset. | |
| 000179XX | 1. Go into the log and note the |
| (System error log might be full) | errors. Clear the log, then |
| run Advanced Diagnostics. | |
| 000181XX | 1. Run Automatic Configuration |
| (The computer requires a network adapter | 2. Network Adapter |
| for remote IPL or a hard disk drive ID of | 3. Hard Disk Drive |
| LUN 0, for IML, neither of these were | 4. System Board |
| detected | |
| 000182XX | (Information only) |
| (Privileged access password (PAP) data is | |
| corrupted. To restore it, move jumper JMP2 to | |
| position '0' write enabled). | |
| 000183XX | 1. Enter the Privileged access |
| (Wrong password entered) | password (PAP) instead of |
| the power-on password. | |
| 000184XX | 1. User must reset the password. |
| (Power-on password corrupted) | |
| 000185XX | 1. Run Select Startup Sequence |
| (Selectable startup sequence corrupted) | utility. Reset user's chosen |
| startup sequence. | |
| 000186XX | 1. Run System Board |
| (Security error, Hardware failed) | |
| 000187XX | 1. Select Set system identification |
| (Vital Product Data (VPD) error. System | from the Reference Diskette, |
| serial number information corrupted) | System Partition (or server |
| image) and type the system serial | |
| number. If problem remains, | |
| suspect the system board. | |
| 000188XX | 1. Run Automatic Configuration |
| (Vital Product Data (VPD) error) | |
| 000189XX | (Information only) |
| (The wrong password was entered | |
| 3 times. Clear the system error log and | |
| restart the system) | |
| 000191XX | 1. Run Advanced Diagnostics |
| (82385 cache test failed) | |
| 000194XX | 1. System Board Memory |
| 2. Memory Riser Card (90) | |
| 3. Memory Module Kit | |
| 000199XX | 1. Run the Flash Update |
| (User indicated configuration is invalid) | Utility (PS/2 9553-xBx Only) |
| 2. System Board | |
| 0001XXXX | 1. System Board |
| (not listed above) | Processor Board (90/95) |
| 2. 486DX33 Upgrade (70/80) | |
| 3. Any Adapter | |
| 4. Bus Adapter | |
| 000201XX 000205XX | 1. System Board Memory |
| (Reseat System Board Memory) | 2. System Board |
| 00020XXY 000217XY | 1. System Board Memory |
| (if the 'Y' digits is in the range | Memory Riser Card (90) |
| 'G' to 'V', suspect the model 90/95 | Processor Board |
| processor board first) | 2. System Board |
| 000210XX 000211XX | 1. Processor Board (90/95) |
| (Check memory) | 2. System board Memory |
| 3. Memory Riser Card (90) | |
| 4. System Board | |
| 000214XX 000215XX | 1. System Board Memory |
| 000216XX 000221XX | Memory Riser Card (90) |
| 000226XX 000240XX | System board |
| 000235XX 000241XX | Processor Board (90/95) |
| (Check memory. It might be the wrong | 2. Bus Adapter |
| type or wrong speed) | |
| 000221XX | 1. System Board |
| (ROM to RAM parity error) | |
| 000231XX | 1. Expanded Memory Option |
| 000235XX | 1. Processor/System Board. |
| Single-Bit (correctable) ECC Memory error | |
| 00024300 00024400 | 1. Processor Board (90/95) |
| 00024500 00024600 | 1. Processor Board |
| (Check memory) | 2. Memory Riser Card (90) |
| 3. System Board | |
| 4. System Board Memory | |
| 00024700 | 1. Processor Board (90/95) |
| 000251XX | (Information only) |
| (Memory location changed on the memory | |
| expansion option) | |
| 000252XX | 1. Processor Board (90/95) |
| 2. System Board | |
| 00025300 00025400 | 1. Processor Cache (90/95) |
| 2. Processor Board | |
| 000255XX | 1. System Board Memory |
| (Check Memory) | 2. System Board |
| 00029000 | 1. Correct the unsupported |
| (Unsupported memory combination | combination of ECC and parity |
| detected) | memory modules. Run Automatic |
| Configuration, then rerun | |
| Advanced Diagnostics | |
| 000291XX 000292XX | 1. Run Automatic Configuration |
| 000293XX 000294XX | then rerun Advanced Diagnostics |
| (Checksum value mismatch) | |
| 000295XX 000296XX | 1. System Board Memory |
| (Check memory for an unsupported | |
| configuration or modules) | |
| 00029800 | 1. System Board Memory |
| (Checksum value mismatch) | Run Automatic Configuration |
| then rerun Advanced Diagnostics | |
| 0002XX00 | 1. 486DX33 Upgrade (70/80) |
| (not listed above) | |
| 000301XX 000302XX | 1. Keyboard Cable |
| 2. System Board | |
| 000303XX 000304XX | 1. System Board |
| 2. Keyboard | |
| 3. Keyboard Cable | |
| 000305XX | 1. Fuse |
| (Keyboard voltage error. If no fuse in system | 2. Keyboard Cable |
| replace system board) | |
| 000306XX | 1. Check for Unsupported Keyboard |
| (Wrong Keyboard attached ?) | |
| 000307XX | 1. Keyboard |
| 2. Keyboard Cable | |
| 000320XX | 1. System Board |
| 000401XX to 000405XX | 1. System Board |
| 0005XXXX | 1. Display Adapter (any type) |
| 000601XX | 1. Defective Diskette |
| 2. Diskette Drive | |
| 2. System Board | |
| 000602XX | 1. Defective Diskette |
| (Invalid boot record) | |
| 000604XX | 1. Diskette Drive |
| (Unsupported drive or cable. | 2. System Board |
| Drive must be media sense type) | 3. Diskette Drive Cable |
| 000605XX | 1. Run Advanced Diagnostics |
| (Diskette drive error) | |
| 000606XX 000607XX | 1. Diskette |
| 000610XX 000621XX | 2. Diskette Drive |
| 000622XX 000623XX | 3. System Board |
| 000624XX 000630XX | |
| 000631XX 000632XX | |
| 000633XX 000640XX | |
| 000641XX 000642XX | |
| 000643XX 000650XX | |
| 000651XX 000652XX | |
| 000653XX 000654XX | |
| 000656XX 000657XX | |
| 000658XX 000659XX | |
| 000660XX | |
| (Generally, these are media errors. | |
| Try a known good diskette. if the | |
| error appears again, replace the drive.) | |
| 000655XX | 1. System Board |
| 000662XX | (Information only) |
| (Wrong drive type installed) | |
| 000663XX | (Information only) |
| (Wrong media type in the drive) | |
| 000668XX | 1. Diskette Drive |
| 0006XXXX | 1. Diskette Drive |
| (not listed above) | 2. System Board |
| 3. Diskette Drive Cable | |
| 0007XXXX | 1. Math Coprocessor |
| For a 486 processor , erase COPROC.DGS | 2. 486DX33 Upgrade (70/80) |
| from the backup Reference Diskette, then | 3. System Board |
| restore the system partition from the | |
| corrected backup Reference Diskette. | |
| Re-run Advanced Diagnostics. | |
| 00265 | (Information only) |
| (Ethernet Adapter terminator not connected) | (Thin/Thick or Twisted Terminator) |
| 00100203 | 1. System Board |
| 00110100 | 1. Run Advanced Diagnostics |
| (Serial connector error, possible system | |
| board failure) | |
| 001101XX 00110200 | 1. System Board |
| 00110600 00110800 | 2. Any Serial Device |
| 00110900 | |
| 001102XX | 1. Run Advanced Diagnostics |
| (Card selected feedback error) | |
| 001103XX | 1. Run Advanced Diagnostics |
| (Port fails register check) | 2. System Board |
| 001106XX | 1. Run Advanced Diagnostics |
| (Serial option cannot be turned off) | 2. System Board |
| 001107XX | 1. Serial Device Cable |
| 2. System Board | |
| 001110XX | 1. Run Advanced Diagnostics |
| (Register test failed) | 2. System Board |
| 001116XX | 1. Run Advanced Diagnostics |
| (16550 interrupt error) | |
| 001117XX | 1. Run Advanced Diagnostics |
| (Failed baud rate test) | |
| 0011XXXX | 1. System Board |
| (not listed above) | |
| (See 'Power Supply Voltage Check' | |
| before replacing system board) | |
| 001201XX | 1. System Board |
| (Check voltages) | 2. Any Serial Device |
| 001202XX 001206XX | 1. Dual Async Adapter/A |
| 001208XX 001209XX | 2. System Board |
| 0012XXXX | 3. Any Serial Device |
| 001207XX | 1. Communications Cable |
| 2. Dual Async Adapter/A | |
| 00129020 | 1. Cached Processor Option |
| (Disk cache error) | 2. System Board |
| 001301XX 001302XX | 1. Game Adapter |
| 2. Joystick | |
| 001402XX | (Information only) |
| (Printer not ready) | |
| 001403XX | (Information only) |
| (No paper error, or interrupt failure) | |
| 001404XX | 1. Run Advanced Diagnostics |
| (System board timeout failure) | |
| 001405XX | 1. Run Advanced Diagnostics |
| (Parallel adapter error) | |
| 001406XX | 1. Run Advanced Diagnostics |
| (Presence test error) | |
| 0014XXXX | 1. Printer |
| (not listed above) | 2. System Board |
| (Check printer before replacing | |
| system board | |
| 001701XX 001703XX | 1. Hard Disk Drive |
| 001704XX 001714XX | 2. Cable (ST506) |
| 0017XXXX | 3. Hard Disk Adapter (ST506) |
| (Not listed below) | 4. System Board |
| 5. Power Supply | |
| 001702XX | 1. Hard Disk Adapter |
| 001705XX 001706XX | 1. Format the Drive |
| 001707XX 001708XX | 2. Hard Disk Drive |
| 001710XX 001711XX | |
| 001712XX 001713XX | |
| 001715XX 001716XX | |
| 001717XX 001726XX | |
| 001735XX 001750XX | |
| 001751XX 001752XX | |
| 001753XX 001754XX | |
| 001755XX 001757XX | |
| 001780XX 001781XX | |
| 001782XX 001790XX | |
| 001791XX | |
| (Read/write problem. Be sure the | |
| drive type is supported. If it is, try | |
| a low level format. If the error continues, | |
| replace the hard disk drive) | |
| 00180100 to 00180700 | 1. System Board |
| 00186XXX | 1. Set Configuration/Features |
| 2. Battery | |
| 0018XXXX | 1. System Board |
| (not listed above) | Expansion Unit |
| 00240100 00240200 | 1. Display (any type) |
| (If screen colors change) | |
| 00240100 00240200 | 1. System Board |
| (If screen colors are OK) | 2. Display (any type) |
| 00240900 | 1. Display (any type) |
| 00241000 | 1. System Board |
| 003015XX | 1. Baseband Adapter |
| (Check for missing wrap or terminator | 2. Baseband Cable |
| plug on the adapter) | |
| 0037XXXX | 1. System Board |
| (This is usually caused by the | 2. Hard Disk |
| SCSI controller built into the | 3. Hard Disk Cable |
| system board. | |
| 004611XX 004630XX | 1. Multiport/2 Interface Board |
| 2. Multiport/2 Adapter | |
| 004612XX 004613XX | 1. Memory Module Package |
| 004640XX 004641XX | 2. Multiport/2 Adapter |
| 00465000 004613XX | 1. Multiport Interface Cable |
| 0046XXXX | 1. Multiport/2 Adapter |
| (not listed above) | 2. Multiport/2 Interface Board |
| 3. Memory module Package | |
| 005600XX | 1. Financial System |
| 2. Controller Adapter | |
| 0062XXXX | 1. 1st Store Loop Adapter |
| 2. Adapter Cable | |
| 0063XXXX | 1. 2nd Store Loop Adapter |
| 2. Adapter Cable | |
| 0064XXXX | 1. Network Adapter |
| (See 'Network Service Procedures') | |
| 0071XXXX | 1. Voice Adapter |
| 0074XXXX | 1. 8514/A Display Adapter |
| (Adapter jumper in the correct position ? | 8514/A Memory Module |
| See 'Display Adapter 8514/A') | 2. System Board |
| 007509XX | 1. Display Adapter (any type) |
| (Check display) | 2. Display (any type) |
| 3. System Board | |
| 4. Video Memory | |
| 007510XX | 1. XGA Adapter |
| (Check display) | 2. Video Memory |
| 0076XXXX | 1. Page Printer Adapter |
| 0078XXXX | 1. High Speed Adapter |
| 0079XXXX | 1. 3117 Adapter |
| 00800100 to 008012XX | 1. Pointing Device (Mouse) |
| (System Board Upgrade Model 50, 55 Only) | 2. System Board |
| 00850X00 00851XXX | 1. 80286 Memory Option Adapter/A |
| 2. System Board | |
| 00852X00 00851XXX | 1. Memory Module Package on |
| the 80286 Memory Adapter/A | |
| 2. Adapter Memory | |
| 3. System Board | |
| 00860100 008602XX | 1. Pointing Device (Mouse) |
| 2. System Board | |
| 008603XX 008604XX | 1. System Board |
| 2. Pointing Device (Mouse) | |
| 0089XXXX | 1. Music Adapter |
| 0091XXXX | 1. Optical Drive |
| 2. Adapter | |
| 0096XXXX | 1. SCSI Adapter |
| (This adapter has cache) | 2. Any SCSI Device |
| 3. System Board | |
| 010001XX | (Information only) |
| (Multiprotocol Adapter/A not found) | |
| 010002XX | 1. Run Advanced Diagnostics |
| (Card selected feedback error) | |
| 010007XX | 1. Communications Cable |
| 2. Multiprotocol Adapter/A | |
| 010008XX 010009XX | 1. Multiprotocol Adapter/A |
| 2. Any Serial Device | |
| 0100XXXX | 1. Multiprotocol Adapter/A |
| (not listed above) | 2. System Board |
| 3. Bus Adapter | |
| 0101102X 0101106X | 1. Modem Adapter/A |
| 0101108X 0101109X | 2. Data/Fax Modem |
| 3. Any Serial Device | |
| 010101XX 010102XX | 1. Have the customer verify |
| 010104XX 010105XX | that the correct operating |
| 010106XX 010107XX | system device drivers are |
| 010108XX 010109XX | installed and operational |
| 010111XX 010112XX | 2. Modem |
| 010103XX 010114XX | |
| 010105XX 010116XX | |
| 010103XX 010110XX | 1. System Board |
| 0101171X | 2. Data/Fax Modem |
| 010117XX | 1. Check system speaker |
| (not listed above) | 2. Check PSTN cable |
| 3. External DAA if installed | |
| 4. Modem | |
| 010118XX | 1. Run System Diagnostics and |
| verify the correct operation of | |
| the modem slot | |
| 2. Modem | |
| 010119XX | 1. Diagnostics detected a |
| Non-IBM modem | |
| 2. Modem | |
| 010120XX | 1. Check PSTN Cable |
| 2. External DAA (if installed) | |
| 3. Modem | |
| 010132XX 010133XX | 1. Modem |
| 010134XX 010135XX | |
| 010136XX 010137XX | |
| 010138XX 010139XX | |
| 010140XX 010141XX | |
| 010142XX 010143XX | |
| 010144XX 010145XX | |
| 010146XX 010147XX | |
| 010148XX 010149XX | |
| 010150XX 010151XX | |
| 010152XX | |
| 010153XX | 1. Data/Fax Modem |
| 2. System Board | |
| 0101XXXX | 1. Modem Adapter/A |
| (not listed above) | 2. Data/Fax Modem |
| 3. System Board | |
| 010450XX 010451XX | 1. Run Advanced Diagnostics |
| 010490XX 010491XX | 2. Riser Card (if installed) |
| 010492XX 010499XX | 3. Hard Disk Drive |
| (Read/write error) | 4. System Board |
| 010452XX | 1. Run Advanced Diagnostics |
| (Seek test error) | |
| 010453XX | (Information only) |
| (Wrong drive type ?) | |
| 010454XX | 1. Run Advanced Diagnostics |
| (Sector buffer test error) | |
| 010455XX 010456XX | 1. Run Advanced Diagnostics |
| (Controller error) | |
| 010459XX | (Information only) |
| (Drive diagnostic command error) | |
| 010461XX | 1. Run Advanced Diagnostics |
| (Drive format error) | |
| 010462XX | 1. Run Advanced Diagnostics |
| (Controller seek error) | |
| 010464XX | 1. Run Advanced Diagnostics |
| (Hard Disk read error) | |
| 010467XX | 1. Run Advanced Diagnostics |
| (Drive non fatal seek error) | |
| 010468XX | 1. Run Advanced Diagnostics |
| (Drive fatal seek error) | |
| 010469XX | 1. Run Advanced Diagnostics |
| (Drive soft error count exceeded) | |
| 010470XX 010471XX | 1. Run Advanced Diagnostics |
| 010472XX | |
| (Controller wrap error) | |
| 010473XX | (Information only) |
| (Corrupt data. Low level might be required | |
| 010480XX | 1. Hard Disk Drive (ESDI) |
| 2. Drive Cable | |
| 3. Controller | |
| 4. System Board | |
| 010481XX | 1. Run Advanced Diagnostics |
| (ESDI drive D seek error) | |
| 010482XX | 1. Run Advanced Diagnostics |
| (Drive select acknowledgement bad) | |
| 010490XX 010491XX | 1. Run Advanced Diagnostics |
| (Drive 0,1 read error) | 2. Riser Card (If installed) |
| 3. Hard Disk Drive | |
| 4. System Board | |
| 010499XX | 1. Run Advanced Diagnostics |
| (Drive controller error) | 2. Riser Card (If installed) |
| 3. Hard Disk Drive | |
| 4. System Board | |
| 010483XX | 1. Hard Disk Adapter (ESDI) |
| 2. System Board | |
| 0104XXXX | 1. Hard Disk Drive |
| (not listed above) | 2. Hard Disk Adapter (ESDI) |
| 3. Hard Disk Cable | |
| 4. Power Supply | |
| 0106XXXX | 1. Ethernet Network Adapter/A |
| (See 'Network Service Procedures') | 2. System Board |
| 3. Bus Adapter | |
| 0107XXXX | 1. 5.25-Inch External Diskette Drive |
| 2. 5.25-Inch Diskette Drive Adapter/A | |
| 0109XXXX | 1. ActionMedia Adapter/A |
| (Check the adapter cables) | 2. System Board |
| 0112XXXX | 1. SCSI Adapter |
| (This adapter does not have cache) | 2. Any SCSI Device |
| 3. System Board | |
| 0119XXXX | 1. 3119 Adapter |
| 0121XXXX | 1. 300/1200/2400 Modem/A |
| 2. Any serial Device | |
| 3. System Board | |
| 01290001 01290002 | 1. Run Advanced Diagnostics |
| 01290003 01290002 | |
| 01290007 01290002 | |
| (Possibly a recoverable processor board error) | |
| 01290050 01290051 | 1. Processor Board |
| 01290052 01290053 | 2. System Board |
| 01290054 01290055 | |
| 01290056 | |
| (Probably a fatal error) | |
| 01290100 012902XX | 1. Processor Board |
| 01290400 01290700 | 2. System Board Cache |
| 01290800 | 3. System Board |
| (Cache error) | |
| 012903XX | 1. Math Coprocessor |
| (Math Coprocessor error) | 2. Processor Board |
| 01290XXX | 1. Processor Cache |
| (not listed above) | 2. Processor Board |
| 3. System Board | |
| 01291200 01291300 | 1. Run Advanced Diagnostics |
| 01291400 012915XX | |
| 012916XX 01291800 | |
| 01291900 01294040 | |
| 01294041 | |
| (Possible processor Board error) | |
| 01291700 | 1. Processor Board (90/95) |
| (If it is a 20 MHz board, and the | |
| processor is a 487SX, the jumper must be | |
| in positions 1 and 2) (487SX is indicated | |
| on the processor) | |
| 01293000 | 1. Jumpered Incorrectly |
| (90/95 Processor board EEPROM jumper is | 2. Processor Board |
| in the wrong position) | |
| 01294042 | 1. Processor Board |
| (POST / BIOS EEPROM error. Update | |
| diskette is required) | |
| 01294400 | 1. Restart the system, then |
| (A hardware default interrupt occurred) | run Advanced Diagnostics |
| 01295050 01295056 | 1. Restart the system, then |
| 01295060 01295061 | run Advanced Diagnostics |
| 01295070 01295071 | |
| 01295072 01295073 | |
| 01295074 01295075 | |
| 01295076 01295077 | |
| 01295078 01295079 | |
| 01295080 01295081 | |
| 01295082 01295083 | |
| 01295085 01295086 | |
| 01295087 01295088 | |
| 01295090 01295091 | |
| 01295094 01295095 | |
| 01295096 01295097 | |
| (Processor board errors) | |
| 0129X300 | 1. Busmaster Adapter (90/95) |
| (Busmaster arbitration error. If more | 2. Processor Board |
| than one is installed, remove them | |
| one at a time to isolate the failure) | |
| 01299000 | 1. Run Automatic Configuration |
| (VPD error, processor board replaced ? | |
| Processor board serial number detected | |
| does not match serial number stored) | |
| 0136XXXX | 1. ISDN Primary Rate Adapter |
| 2. System Board | |
| 0137XXXX | 1. System Board |
| 0141XXXX | 1. Realtime Interface Coprocessor |
| Portmaster Adapter | |
| 0143XXXX | 1. Japanese Display Adapter |
| 2. System Board | |
| 01471000 014711XX | 1. System Board Display Adapter (any type) |
| 2. Adapter Video Memory | |
| 0148XX00 | 1. Display Adapter (any type) |
| 014901XX 014902XX | 1. Display Adapter (any type) |
| 01491XXX 014922XX | 2. System Board |
| 3. Display (any type) | |
| 014932XX | 1. External Display (any type) |
| 2. Display Adapter (any type) | |
| 0152XXXX | 1. XGA Display Adapter/A |
| 2. System Board | |
| 015302XX | 1. S/370 Channel Emulator/A Adapter |
| 015304XX | 1. S/370 Channel Emulator/A Adapter |
| 2. S/370 Emulator/A Channel Cable | |
| 0161XXXX | 1. FaxConcentrator Adapter/A |
| 0164XXXX | 1. 120MB Internal Tape Drive |
| 2. Diskette Cable | |
| 3. System Board | |
| 016500XX | 1. 6157 Tape Attachment Adapter |
| 016520XX 016540XX | 1. 6157 Streaming Tape Drive |
| 2. 6157 Tape Attachment Adapter | |
| 0166XXXX 0167XXXX | 1. Token-Ring Network Adapter/A |
| (See 'Network Service Procedures') | 2. System Board |
| 3. Bus Adapter | |
| 018001XX | 1. Wizard Adapter |
| (18001 to 18029) | 2. Wizard Adapter Memory |
| 018031XX | 1. Wizard Adapter Cable |
| (18031 to 18039) | |
| 018441XX | (Information only) |
| Unsupported memory module on 80386 adapter) | |
| 018451XX | (Information only) |
| (Need to reconfigure. Module changed | |
| on 80386 adapter) | |
| 0184XXXX | 1. Enhanced 80386 Memory Adapter/A |
| 0185XXXX | 1. DBCS Japanese Display Adapter/A |
| 2 System Board | |
| 0194XXXX | 1. Memory Module Package on the |
| 2-8MB80286 Memory Adapter | |
| 2. Memory adapter | |
| 3. System Board | |
| 020001XX to 020003XX | 1. Image Adapter/A |
| Image-I Adapter/A | |
| 2. Memory Module DRAM or VRAM | |
| 020004XX | 1. Memory Module DRAM or VRAM |
| 2. Image Adapter/A Image-I Adapter/A | |
| 020005XX to 020010XX | 1. Image Adapter/A |
| Image-I Adapter/A | |
| 2. Memory Module DRAM or VRAM | |
| 0200XXXX | 1. Image Adapter/A |
| (not listed above) | Image-I Adapter/A |
| 2. Memory Module DRAM or VRAM | |
| 3. System Board | |
| 020101XX to 020103XX | 1. Printer/Scanner Option |
| 2. Image Adapter/A | |
| 3. Memory Module DRAM or VRAM | |
| 020104XX | 1. Memory Module DRAM or VRAM |
| 2. Printer/Scanner Option | |
| 3. Image Adapter/A | |
| 020105XX to 020110XX | 1. Printer/Scanner Option |
| 2. Image Adapter/A | |
| 3. Memory Module DRAM or VRAM | |
| Image Adapter/A Memory Test failure | 1. Replace memory module |
| indicated by graphic representation | (shown in graphic) |
| of adapter | |
| 0206XXXX | 1. SCSI-2 Adapter |
| 2. Any SCSI Device | |
| 3. System Board | |
| 0208XXXX | 1. Any SCSI Device |
| (Verify that there are no duplicate | |
| SCSI ID settings on the same bus) | |
| for Error Code Format see > | SCSI/Non-SCSI Error Code Format Codes |
| for 0210XXXX 9xxx Error's see > | SCSI Fixed Disk Diagn. Return Codes |
| 0210XXXA (60MB) | 1. SCSI Hard Disk Drive |
| 0210XXXB (80MB) | 2. SCSI Adapter or the SCSI controller |
| 0210XXXC (120MB) | built into the system board. |
| 0210XXXD (160MB) | 3. SCSI Cable |
| 0210XXXE (320MB) | 4. SCSI ID Switch (On some models) |
| 0210XXXF (400MB) | |
| 0210XXXG (40MB) | |
| 0210XXXH (1GB) | |
| 0210XXXI (104MB) | |
| 0210XXXJ (212MB) | |
| 0210XXXM (2GB 8 bit 68-pin) | |
| 0210XXXN (540MB) | |
| 0210XXXO (1GB) | |
| 0210XXXQ (540MB) | |
| 0210XXXP (2GB 8 bit 50-pin) | |
| 0210XXXU (Size unknown) | |
| (If it is an external device, check the | |
| external voltages. | |
| See 'SCSI Diagnostic Tests' and | |
| 'SCSI ID (Using to Help Isolate Failures' | |
| before replacing any FRUs) | |
| 0210XXXX | 1. SCSI Hard Disk Drive |
| (Internal bus, size unknown) | 2. SCSI Adapter or the SCSI controller |
| built into the system board | |
| 0210XXX1 | 3. SCSI Cable |
| (External bus, size unknown) | 4. SCSI ID Switch (on some models) |
| The amber LED remains on. | 1. Tape Drive |
| 2. SCSI Cable (internal) | |
| 3. SCSI Adapter or the SCSI controller | |
| built into the system board. | |
| The green 'in use' LED fails to come on. | 1. Tape Drive |
| 2. SCSI Adapter or the SCSI controller | |
| built into the system board. | |
| 3. SCSI Cable (internal) | |
| SCSI Cable (external) | |
| The tape is automatically ejected from | 1. Tape Cassette |
| the drive. | 2. Drive |
| SCSI ID on the rotary switch does not | 1. Rotary Switch Circuit Board |
| match the SCSI ID set in configuration. | 2. Circuit Board Cable |
| (Verify the drive switches inside the cover | 3. Tape Drive |
| are set to zero) | |
| Tape sticks/breaks in the drive. | 1. Tape Cassette |
| (Verify that the tapes used meet | |
| ANSI standard X3B5) | |
| 0212XXXX | 1. SCSI Printer |
| 2. Printer Cable | |
| 0213XXXX | 1. SCSI Processor |
| 0214XXXX | 1. WORM Drive |
| 0215XXXC | 1. CD-ROM Drive I |
| 0215XXXD | CD-ROM Drive II |
| 0215XXXE | Enhanced CD-ROM Drive II |
| 0215XXXU | Any CD-ROM Drive |
| If it is an external device, and the | 2. SCSI Cable |
| power-on LED is off, check external voltages) | 3. SCSI Adapter or the SCSI controller |
| built into the system board. | |
| 0216XXXX | 1. Scanner |
| 0217XXXX | 1. Rewriteable Optical Drive |
| (If it is an external device, and the | 2. SCSI Adapter or the SCSI controller |
| power-on LED is off, check external voltages) | built into the system board. |
| 3. SCSI Cable | |
| 0218XXXX | 1. Changer |
| (Check for multi CD tray, or juke box) | |
| 0219XXXX | 1. SCSI Communications Device |
| 024201Y0 024210Y0 | 1. ISDN/2 Adapter |
| (Be sure the wrap plug is not missing) | 2. ISDN/2 Wrap Plug |
| 3. ISDN/2 Communications Cable | |
| 0243XXXX | 1. XGA-2 Display Adapter |
| 002460XX | 1. 90 MHz Processor Upgrade |
| (without VRAM) | |
| 2. System Board | |
| 002461XX | 1. 90 MHz Processor Upgrade |
| (with 1MB VRAM) | |
| 0258XXXX | 1. XGA-2 Display Adapter |
| Video might have failed. | 2. System Board |
| (Ensure that you are using diagnostic files | |
| XGAANI.DGS and XGAPNI.DGS dated 03/06/93 | |
| or later before you replace any FRUs. | |
| Earlier files cause erroneous errors.) | |
| 0259XXXX | 1. SVGA Adapter |
| 2. System Board | |
| 0260XXXX | 1. System Board |
| 2. Any SCSI Device | |
| 0270XXXX | 1. RAID Adapter Controller |
| 2. System Board | |
| 0271XXXX | 1. RAID Hard Disk Drive |
| 2. System Board | |
| 0273XXXX | 1. 1 Mbps MicroChannel Infrared |
| 2. LAN Adapter | |
| 027485Y0 | 1. LANStreamer MC 16 Adapter |
| Configuration Compare failure | |
| 027490Y0 | 1. LANStreamer MC 16 Adapter |
| Adapter Card Test failure | |
| 027491Y0 | 1. LANStreamer MC 16 Adapter |
| Open Phase Test failure | |
| 027492Y0 | 1. LANStreamer MC 16 Adapter |
| Computer Problem | |
| 027493Y0 | 1. LANStreamer MC 16 Adapter |
| Transmit/Receive Test failure | |
| Check Adapter Cable/Wrap Plug | |
| 027499Y0 | 1. LANStreamer MC 16 Adapter |
| General error | |
| 0274XXY0 | 1. LANStreamer MC 16 Adapter |
| Y is SLOT # where Adapter installed | |
| 2. System Board | |
| 027501XX 027503XX | 1. ServerGuard Adapter |
| 027506XX 027507XX | 2. System Board |
| 027502XX 027504XX | 1. ServerGuard Adapter |
| 027510XX 027511XX | |
| 027533XX 027534XX | |
| 027536XX 027537XX | |
| 027509XX | 1. Remove redundant ServerGuard |
| Adapters, run Auto Configuration | |
| program, then retest | |
| 027512XX | 1. WMSELF.DGS diagnostics file missing |
| 2. WMSELF.DGS diagnostic file incorrect | |
| 027535XX | 1. 3V Lithium Backup Battery |
| 2. ServerGuard Adapter | |
| 027554XX | 1. Internal Temperature out of range |
| 2. ServerGuard Adapter | |
| 027555XX 027556XX | 1. ServerGuard Adapter |
| 2. System Power Supply | |
| 027557XX | 1. 7.2V NiCad Main Battery Pack |
| 2. ServerGuard Adapter | |
| 027558XX 027559XX | 1. PCMCIA Type II Modem |
| 027560XX 027561XX | 2. ServerGuard Adapter |
| 027562XX | 1. External Power Control Box |
| not connected | |
| 2. External Power Control Box | |
| 3. ServerGuard Adapter | |
| 027563XX 027564XX | 1. External Power Control Box |
| 2. ServerGuard Adapter | |
| 0275XXXX | 1. Update Diagnostic Software |
| 027801X0 027859X0 | 1. Personal Voice Dictation Adapter/A |
| 027861X0 027863X0 | 1. OS/2 Device Driver for Voice Dictation Adapter/A is missing |
| 027864X0 | 1. Only one Voice Dictation PCMCIA Adapter is supported in a computer |
| 027865X0 | 1. The PCMCIA enabler is unable to read the card information |
| 027866X0 | 1. PCMCIA Card Socket Services not installed |
| 027871X0 | 1. The VoiceType Dictation PCMCIA Card was not found |
| 027880X0 027889x0 | 1. Check all Cables |
| (Speaker test failed) | 2. Check external Speaker oper. control. |
| 027890X0 027899x0 | 1. Check all Cables |
| (Microphone test failed) | 2. Check Microphone operating control. |
| 0279XXXX | 1. Fast/Wide Streaming - |
| - RAID Adapter/A (FRU 06H3059) | |
| Pass through Card & Cable | |
| 2. System Board | |
| 3. Signal Pass Through Card (if installed) | |
| 0281XXY0 | 1. Dual LANStreamer MC32 Adapter |
| Y = slot number | XX = 85 Configuration Compare failure |
| XX = type of error | XX = 90 Adapter Test Card failure |
| XX = 91 Open Phase Test failure | |
| XX = 92 Computer Problem | |
| XX = 93 Transmit/Receive Test failure | |
| XX = 99 General error | |
| I998009X | 1. Restore System Partition |
| I999XXXX | 1. Default Hard Disk Drive |
| (This is usually not a hardware failure. | 2. Processor Board (90/95) |
| Go to IML and IPL Errors before replacing | 3. SCSI Adapter |
| FRUs. Specific I999XXXX error codes | 4. SCSI Cable |
| are listed after IML and IPL Errors | |
| for SCSI 0210xxxx 9xxx (Fixed Disk DIAGNOSE) Errorcodes see > SCSI Return Error-Codes |
Please see the LEGAL - Trademark notice.
Feel free - send a 
for any BUG on this page found - Thank you.