Return to MAIN-Index  Return to SUB-Index    IBM-AUSTRIA - PC-HW-Support    30 Aug 1999

RAID Backplane III and Narrow/Wide Hot Swap Tray Option



  Narrow/Wide Hot Swap Tray III Option (Installation)
This Backplane III type is used in machines 3517, 3518, 8641-520, 8642-720

Tray Installation Instruction for 

Tray - Hard Disks - Backplane PNs 

  Backplane III    FRU PN   (06H8629)  76H2671
  BackPlane III    OPT PN   (70G9855)  76H2670    UPOS SHSBP3Y
 -------------------------------------------------------------------
  RAID Hot Swap HDD III with 2x LED + button     ZG96-0121
  Prerequ. 'AUTOBAHN'- type III Backplane or 3517 - 3518
  Option with Harddisk.
  HDD and Tray       1.12GB        2.25GB        4.5(5.0)GB
 ------------------|-------------|-------------|---------- OPTION  --
  Tray UPOS-P/N    | S1GHS2Y     | S2GHS2Y     | S4GHS2Y
  Mfg. P/N         | 70G9861 1.) | 70G9862 1.) | 70G9863
 -------------------------------------------------------------------
 Note 1 see > ECA012
 --------------------------------------------------------- FRU P/N  -
  Drive Tray III   | 06H8631     | 06H8631     | 06H8631
  incl. SCSI 16-bit cable and LED/button cable, but w/o ID cable
 ------------------|-------------|-------------|--------------------
  Backplane to     | 06H8644     | 06H8644     | 06H8644
  Backplane Data Cable 200mm (8.5 - Inch)      |
 ------------------|-------------|-------------|--------------------
  SCSI ID Cable    | 06H8664     | 06H7691     | 06H7691
 ------------------|-------------|-------------|--------------------
  LED/button cable | 07H1696     | 07H1696     | 07H1696
 ------------------|-------------|-------------|--------------------
  Harddisk         | 06H8560     | 42H1821     | 76H0959
                   |             | 76H0958     |
 ------------------|-------------|-------------|--------------------
  Screw (qty. 4)   | 1147429     | 1147429     | 1147429
 -------------------------------------------------------------------


 


SCSI-2 F/W Hot-Swap Drive Tray III UPOS SHST05Y Mfkg PN 70G9860.
For Tray with 2 LEDs/Button - FRUs see above

This Wide-Option is w/o harddisk and includes: DASD Tray complete, two SCSI ID cables, screws, and installation instruction.

SCSI-2 Fast Hot-Swap Drive Tray III UPOS SHST04Y
Same as above but for NARROW hard disk, Ultrastar XP 2.25GB SCSI Hard Disk Drive (Fast OSC2GBM FRU 06H3370)

RAID Backplane III - Location/Jumper

 

Setting the Backplane III - Address Jumper - J2

If more than one backplane is installed in your server or expansion enclosure, each backplane address jumper must have a unique setting. This setting identifies the backplane's location within the server or expansion enclosure and ensures proper operation.

Locate the three-pin address jumper (J2) on the back of the backplane.
Jumper Position    Description
E    Address for a backplane installed in Bank E
D    Address for a backplane installed in Bank D
C    Address for a backplane installed in Bank C


Setting Backplane III - SCSI ID Jumpers - J12

The SCSI ID address jumper, a pin block with four pairs of pins (J12), is located on the rear of the backplanes in banks C, D and E. When two backplanes are daisy chained in your server or expansion enclosure, the first backplane address jumper (for example, Bank C) must be set to LOW , defining the SCSI IDs as 0 through 5. The second backplane (in this example, bank D), must be set to either HI  or Reverse , defining the SCSI IDs as 5 through 0, or HI, defining the SCSI IDs as 8 to D. The default, no jumper installed, is to set the addresses LO.

If the SCSI adapter supports more than eight SCSI devices per SCSI channel, the second backplane can be set to either HI or Reverse. However, if the SCSI Adapter supports eight or fewer SCSI devices per SCSI channel, the second backplane must be set to Reverse.

 Jumper Position         Description
 ----------------------------------------------------------------
       2 4 6 8
 J12   ° ° ° °   LO      Sets SCSI IDs to LO, starting from SCSI
       ° ° ° °           ID 0 (bay 1) to SCSI ID 5 (bay 6)
       1 3 5 7           (No jumper required)
 ----------------------------------------------------------------
       2 4 6 8
 J12   ° ° | °   LO      Sets SCSI IDs to LO and Reverse,
       ° ° | °           starting from SCSI ID 5 (bay 1)
       1 3 5 7           to SCSI ID 0 (bay 6)
 ----------------------------------------------------------------
       2 4 6 8
 J12   ° | ° °   HI      Sets SCSI IDs to HI, starting from SCSI
       ° | ° °           ID 8 (bay 1) to SCSI ID D (bay 6)
       1 3 5 7


Back to  Jump to TOP-of-PAGE
More INFORMATION / HELP is available at the  IBM-HelpCenter

Please see the LEGAL  -  Trademark notice.
Feel free - send a Email-NOTE  for any BUG on this page found - Thank you.