|
|
|
| Symptom/Error | FRU/Action |
|---|---|
| 10X | 1. System Board |
| 110 | 1. Go to 'Memory Checkout' |
| 2. IC DRAM Card or DIMM Card | |
| 3. System Board | |
| 111 | 1. Go to 'Memory Checkout' |
| 2. Expansion Unit/Port Replicator | |
| 3. System Board | |
| 118 (Memory parity error | 1. Run memory diagnostics to clear |
| was logged in CMOS.) | the error log. |
| (Go to 'Memory Checkout') | |
| 158 (HDP was not set | 1. Set a HDP. |
| even though the supervisor | |
| password is set.) | |
| 159 (HDP is not set | 1. Set a correct HDP. |
| the same as the supervisor password.) | |
| 161 | 1. Go to 'Checking the Backup Battery' |
| 2. Backup Battery | |
| 3. System Board | |
| 163 (Time and Date was not set.) | 1. Set Time and Date. |
| 2. System Board | |
| 173 (Configuration data were lost.) | 1. Select OK in the error screen, |
| then set time and date | |
| 2. Backup Battery | |
| 3. System Board | |
| 174 (Perform | 1. Check Device Configuration. |
| 'Checking the Installed Devices List' | 2. System Board |
| before changing any FRUs.) | 3. Diskette Drive Assembly |
| 4. Hard Disk Drive Assembly | |
| 175, 177, 178 | 1. System Board |
| 183 (Incorrect password | 1. Have the user examine the password. |
| entered at the supervisor | |
| password prompt.) | |
| 184 (POP checksum error.) | 1. Reset the POP in Easy-Setup. |
| 185 (The startup sequence is | 1. Reset the startup sequence |
| not valid. Suspect that | in Easy-Setup. |
| power was off when the | |
| startup sequence was | |
| being updated.) | |
| 186 | 1. System Board |
| 188 | 1. Set the system identification |
| using the ThinkPad 750Ce hardware | |
| maintenance diskette. | |
| NOTE: | |
| You can use this maintenance | |
| diskette for all Models. | |
| 190 (Depleted battery pack | 1. Go to 'Checking the Battery Pack' |
| was installed when the | |
| power was on.) | |
| 191XX | 1. System Board |
| 2. Processor card | |
| (370C, 750Ce, 755C, and 755Cs) | |
| 195 (The configuration read | 1. Check if the configuration was changed. |
| from the hibernation area | For example, check if the disk drive |
| does not match the actual | from another computer. |
| configuration.) | |
| 196 (Read error occurred | 1. Run the hard disk drive test. |
| in the hibernation area | 2. Hard Disk Drive |
| of the HDD.) | |
| 197 (The computer memory | 1. Have the user disable then |
| size is not equal to the | enable hibernation mode. |
| hibernation area size on | |
| the HDD.) | |
| 199XX | 1. System Board |
| 1XX | 1. System Board |
| 2XX | 1. Go to 'Memory Checkout' |
| 2. IC DRAM Card, DIMM, or DIMM Adapter | |
| 3. System Board | |
| 301, 303, 304, 305, 3XX | 1. Go to 'Keyboard/Aux. Inp.-Device Checkout' |
| 2. Keyboard | |
| 3. Interposer Card | |
| 4. External Numeric Keypad | |
| 5. External Keyboard | |
| 6. Keyboard/Mouse Cable | |
| 7. System Board | |
| 601, 6XX | 1. Go to 'Diskette Drive Test' |
| 2. Diskette Drive Assembly | |
| 3. Diskette | |
| 4. System Board | |
| 602 (Diskette read error.) | 1. Go to 'Diskette Drive Test' |
| 2. Diskette | |
| 3. Diskette Drive Assembly | |
| 604 (Non-acceptable ID | 1. Go to 'Diskette Drive Test' |
| was read from the diskette drive.) | 2. Diskette Drive Assembly |
| 3. System Board | |
| 11XX | 1. Serial Device (First) |
| 2. Communication Cable | |
| 3. System Board | |
| 12XX | 1. Serial Device (Second) |
| 2. Communication Cable | |
| 3. System Board | |
| 17XX | 1. Hard Disk Drive |
| 2. System Board | |
| 24XX | 1. System Board |
| 4101 | 1. Reseat the LCD connector Pen |
| see '2070 LCD Assembly' | |
| 2. LCD Assembly | |
| 3. System Board | |
| 808X | 1. PCMCIA Slot Assembly |
| 2. PCMCIA Device | |
| 3. System Board | |
| 860X (Pointing device error | 1. External Mouse |
| when TrackPoint II is disabled.) | 2. External Keyboard |
| 3. System Board | |
| 861X (Pointing device error | 1. Reseat the keyboard |
| when TrackPoint II is enabled.) | Track Point II cable at |
| the interposer card | |
| 355x, 360x | |
| See '1040 Keyboard Unit' | |
| 370C, 750x, 755C, 755Cs | |
| See '2040 Keyboard Unit' | |
| 2. Keyboard | |
| 3. External Mouse | |
| 4. System Board | |
| I9990301 | 1. Reseat the boot device. |
| I9990302 | 2. Check the startup sequence for the |
| I9990305 | correct boot device. |
| 3. Check that operating system has no | |
| failure, or is installed correctly. | |
| I9990303 | 1. System Board |
| Other codes not listed above | 1. Go to 'Undetermined Problems' |
Please see the LEGAL - Trademark notice.
Feel free - send a 
for any BUG on this page found - Thank you.