MANUAIS DE MOTHERBOARDS SUPERMICRO

440BX Based  Motherboard Jumper Settings

  SUPER P6DBU  SUPER P6DBS   SUPER P6DBE   SUPER P6SBU  SUPER P6SBS   SUPER P6SBA

 

SUPER P6DBU JUMPER SETTINGS

  • CPU Settings: (If using dual processors, both processors must have the same speed and processor CPUID.)

CPU Core/Bus Ratio Jumper Settings
Ratio JB1 JB2 JB3 JB4
X 3.0 ON OFF ON ON
X 3.5 OFF OFF ON ON
X 4.0 ON ON OFF ON
X 4.5 OFF ON OFF ON
X 5.0 ON OFF OFF ON
X 5.5 OFF OFF OFF ON
X 6.0 ON ON ON OFF

Example:

For Pentium II 400MHz CPU:
bus speed = 100MHz,
Core/Bus Ratio = X 4.0

the jumper settings should be: JP11:OFF,JB1:ON,JB2:ON,
JB3:OFF,JB4:ON

 

 

Bus Speed Selection (JP11)
JP11 (2-pin jumper) JP11 (3-pin jumper)
ON OFF (Default) OFF 1-2 2-3
66 MHz Auto (determined by CPU 66/100 pin) 100 MHz Auto (determined by CPU 66/100 pin) 66 MHz

 

  • CMOS/Battery:
    • JBT1: CMOS Clear, pin 1-2: Normal(default), pin 2-3: CMOS Clear (To clear CMOS needs to disconnect AC power.)
    • JBT2: Optional External battery, pin1: +3V, pin2 and pin3: No Connect, pin4: Ground
  • Front Control Panel:
    • JF1:
      • IDE LED: pin1:+5V, pin2:HD Active, pin3:HD Active, pin4:+5V
      • Power LED: pin5:Vcc +5V, pin6: Vcc +5V, pin7: Ground
      • Keylock: pin8: Keyboard Inhibit, pin9:Ground
      • Speaker: pin10: Vcc +5V, pin11 and pin12: No Connect, pin13:Speaker Data
    • JF2:
      • Infrared Connector: pin1:Vcc +5V, pin2: Key, pin3: IRRX, pin4:Ground, pin5:IRTX, pin6-pin8: No Connect
      • Power-ON: pin9: PW_ON, pin10: Ground, pin11:No Connect
      • Reset: pin12: Ground, pin13:Reset

     

  • SCSI:
    • SLED: SCSI LED Connector, pin1 and pin4 :Vcc, pin2 and pin3: SCSI LED# Signal
    • S_TERM: SCSI Termination, ON (default): Terminated, OFF: Un-terminated

 

  • Overheat/Thermal Control:
    • BZ_ON: Buzzer On, ON(default): Enable On-board Buzzer (Turn on the buzzer when overheat occurs), OFF: Disable On-board Buzzer
    • JOH1: Overheat LED Connector, pin1: Overheat Data, pin2: +12V

     

  • Power On Control:
    • JP20: Power_ON Control,
      • pin 1-2: Power Up Automatically With The First Time AC power Applied
      • pin 2-3 (default): Controlled By The Power_ON Jumper (JF2  pin9 and pin10).
    • WOL:Wake-On-LAN Connector, pin1: +5V Standby Power, pin2: Ground, pin3:Wake Up Pulse

     

  • Others:
    • JL1: Chassis Intrusion Connector, OFF: Default, ON: Intrusion (pin1: Intrusion Input, pin2:Ground)
    • J36: Extra Power Connector, pin1-pin3: Ground, pin4 & pin5: +3.3V, pin6: +5V
    • JP18 & JP16: Unused (OFF)

   

SUPER P6DBS JUMPER SETTINGS

  • CPU Settings: (If using dual processors, both processors must have the same speed and processor CPUID.)

CPU Core/Bus Ratio Jumper Settings
Ratio JB1 JB2 JB3 JB4
X 3.0 ON OFF ON ON
X 3.5 OFF OFF ON ON
X 4.0 ON ON OFF ON
X 4.5 OFF ON OFF ON
X 5.0 ON OFF OFF ON
X 5.5 OFF OFF OFF ON
X 6.0 ON ON ON OFF

Example:

For Pentium II 400MHz CPU:
bus speed = 100MHz,
Core/Bus Ratio = X 4.0

the jumper settings should be: JP11:OFF,JB1:ON,JB2:ON,
JB3:OFF,JB4:ON

 

 

Bus Speed Selection (JP11)
JP11 (2-pin jumper) JP11 (3-pin jumper)
ON OFF (Default) OFF 1-2 2-3
66 MHz Auto (determined by CPU 66/100 pin) 100 MHz Auto (determined by CPU 66/100 pin) 66 MHz

 

  • CMOS/Battery:
    • JBT1: CMOS Clear, pin 1-2: Normal(default), pin 2-3: CMOS Clear (To clear CMOS needs to disconnect AC power.)
    • JBT2: Optional External battery, pin1: +3V, pin2 and pin3: No Connect, pin4: Ground

 

  • Front Control Panel:
    • JF1:
      • IDE LED: pin1:+5V, pin2:HD Active, pin3:HD Active, pin4:+5V
      • Power LED: pin5:Vcc +5V, pin6: Vcc +5V, pin7: Ground
      • Keylock: pin8: Keyboard Inhibit, pin9:Ground
      • Speaker: pin10: Vcc +5V, pin11 and pin12: No Connect, pin13:Speaker Data
    • JF2:
      • Infrared Connector: pin1:Vcc +5V, pin2: Key, pin3: IRRX, pin4:Ground, pin5:IRTX, pin6-pin8: No Connect
      • Power-ON: pin9: PW_ON, pin10: Ground, pin11:No Connect
      • Reset: pin12: Ground, pin13:Reset

 

  • SCSI:
    • S_LED: SCSI LED Connector, pin1 and pin4 :Vcc, pin2 and pin3: SCSI LED# Signal
    • JA5 & JA6: SCSI Termination, ON (default): Terminated, OFF: Un-terminated

     

  • Overheat/Thermal Control:
    • BZ_ON (for PCB rev.2.00): Buzzer On, ON(default): Enable On-board Buzzer (Turn on the buzzer when overheat occurs), OFF: Disable On-board Buzzer
    • JOH1: Overheat LED Connector, pin1: Overheat Data, pin2: +12V

 

  • Power On Control:
    • JP20: Power_ON Control,
      • pin 1-2: Power Up Automatically With The First Time AC power Applied
      • pin 2-3 (default): Controlled By The Power_ON Jumper (JF2  pin9 and pin10).
    • WOL:Wake-On-LAN Connector, pin1: +5V Standby Power, pin2: Ground, pin3:Wake Up Pulse

 

  • Others:
    • JL1: Chassis Intrusion Connector, OFF: Default, ON: Intrusion (pin1: Intrusion Input, pin2:Ground)
    • Power_SEC (for PCB rev.2.00): Extra Power Connector, pin1-pin3: Ground, pin4 & pin5: +3.3V, pin6: +5V
    • JP18 & JP16: Unused (OFF)

SUPER P6DBE JUMPER SETTINGS

  • CPU Settings: (If using dual processors, both processors must have the same speed and processor CPUID.)

CPU Core/Bus Ratio Jumper Settings
Ratio JB1 JB2 JB3 JB4
X 3.0 ON OFF ON ON
X 3.5 OFF OFF ON ON
X 4.0 ON ON OFF ON
X 4.5 OFF ON OFF ON
X 5.0 ON OFF OFF ON
X 5.5 OFF OFF OFF ON
X 6.0 ON ON ON OFF

Example:

For Pentium II 400MHz CPU:
bus speed = 100MHz,
Core/Bus Ratio = X 4.0

the jumper settings should be: JP11:OFF,JB1:ON,JB2:ON,
JB3:OFF,JB4:ON

 

 

Bus Speed Selection (JP11)
JP11 (2-pin jumper) JP11 (3-pin jumper)
ON OFF (Default) OFF 1-2 2-3
66 MHz Auto (determined by CPU 66/100 pin) 100 MHz Auto (determined by CPU 66/100 pin) 66 MHz

 

  • CMOS/Battery:
    • JBT1: CMOS Clear, pin 1-2: Normal(default), pin 2-3: CMOS Clear (To clear CMOS needs to disconnect AC power.)
    • JBT2: Optional External battery, pin1: +3V, pin2 and pin3: No Connect, pin4: Ground
  • Front Control Panel:
    • JF1:
      • IDE LED: pin1:+5V, pin2:HD Active, pin3:HD Active, pin4:+5V
      • Power LED: pin5:Vcc +5V, pin6: Vcc +5V, pin7: Ground
      • Keylock: pin8: Keyboard Inhibit, pin9:Ground
      • Speaker: pin10: Vcc +5V, pin11 and pin12: No Connect, pin13:Speaker Data
    • JF2:
      • Infrared Connector: pin1:Vcc +5V, pin2: Key, pin3: IRRX, pin4:Ground, pin5:IRTX, pin6-pin8: No Connect
      • Power-ON: pin9: PW_ON, pin10: Ground, pin11:No Connect
      • Reset: pin12: Ground, pin13:Reset

     

  • Overheat/Thermal Control:
    • BZ_ON: Buzzer On, ON(default): Enable On-board Buzzer (Turn on the buzzer when overheat occurs), OFF: Disable On-board Buzzer
    • JOH1: Overheat LED Connector, pin1: Overheat Data, pin2: +12V

     

  • Power On Control:
    • JP20: Power_ON Control,
      • pin 1-2: Power Up Automatically With The First Time AC power Applied
      • pin 2-3 (default): Controlled By The Power_ON Jumper (JF2  pin9 and pin10).
    • WOL:Wake-On-LAN Connector, pin1: +5V Standby Power, pin2: Ground, pin3:Wake Up Pulse

     

  • Others:
    • JL1: Chassis Intrusion Connector, OFF: Default, ON: Intrusion (pin1: Intrusion Input, pin2:Ground)
    • J36: Extra Power Connector, pin1-pin3: Ground, pin4 & pin5: +3.3V, pin6: +5V
    • JP18 & JP16: Unused (OFF)

  

SUPER P6SBU JUMPER SETTINGS

  • CPU Settings:

CPU Core/Bus Ratio Jumper Settings
Ratio JB1 JB2 JB3 JB4
X 3.0 ON OFF ON ON
X 3.5 OFF OFF ON ON
X 4.0 ON ON OFF ON
X 4.5 OFF ON OFF ON
X 5.0 ON OFF OFF ON
X 5.5 OFF OFF OFF ON
X 6.0 ON ON ON OFF

Example:

For Pentium II 400MHz CPU:
bus speed = 100MHz,
Core/Bus Ratio = X 4.0

the jumper settings should be: JP11:OFF,JB1:ON,JB2:ON,
JB3:OFF,JB4:ON

 

 

Bus Speed Selection (JP11)
JP11 (2-pin jumper) JP11 (3-pin jumper)
ON OFF (Default) OFF 1-2 2-3
66 MHz Auto (determined by CPU 66/100 pin) 100 MHz Auto (determined by CPU 66/100 pin) 66 MHz

 

  • CMOS/Battery:
    • JBT1: CMOS Clear, pin 1-2: Normal(default), pin 2-3: CMOS Clear (To clear CMOS needs to disconnect AC power.)
    • JBT2: Optional External battery, pin1: +3V, pin2 and pin3: No Connect, pin4: Ground
  • Front Control Panel:
    • JF1:
      • IDE LED: pin1:+5V, pin2:HD Active, pin3:HD Active, pin4:+5V
      • Power LED: pin5:Vcc +5V, pin6: Vcc +5V, pin7: Ground
      • Keylock: pin8: Keyboard Inhibit, pin9:Ground
      • Speaker: pin10: Vcc +5V, pin11 and pin12: No Connect, pin13:Speaker Data
    • JF2:
      • Infrared Connector: pin1:Vcc +5V, pin2: Key, pin3: IRRX, pin4:Ground, pin5:IRTX, pin6-pin8: No Connect
      • Power-ON: pin9: PW_ON, pin10: Ground, pin11:No Connect
      • Reset: pin12: Ground, pin13:Reset

     

  • SCSI:
    • SLED: SCSI LED Connector, pin1 and pin4 :Vcc, pin2 and pin3: SCSI LED# Signal
    • S_TERM: SCSI Termination, ON (default): Terminated, OFF: Un-terminated

 

  • Overheat/Thermal Control:
    • BZ_ON: Buzzer On, ON(default): Enable On-board Buzzer (Turn on the buzzer when overheat occurs), OFF: Disable On-board Buzzer
    • JOH1: Overheat LED Connector, pin1: Overheat Data, pin2: +12V

     

  • Power On Control:
    • JP20: Power_ON Control,
      • pin 1-2: Power Up Automatically With The First Time AC power Applied
      • pin 2-3 (default): Controlled By The Power_ON Jumper (JF2  pin9 and pin10).
    • WOL:Wake-On-LAN Connector, pin1: +5V Standby Power, pin2: Ground, pin3:Wake Up Pulse

     

  • Others:
    • JL1: Chassis Intrusion Connector, OFF: Default, ON: Intrusion (pin1: Intrusion Input, pin2:Ground)
    • J36: Extra Power Connector, pin1-pin3: Ground, pin4 & pin5: +3.3V, pin6: +5V
    • JP18 & JP16: Unused (OFF)

   

SUPER P6SBS JUMPER SETTINGS

  • CPU Settings:

CPU Core/Bus Ratio Jumper Settings
Ratio JB1 JB2 JB3 JB4
X 3.0 ON OFF ON ON
X 3.5 OFF OFF ON ON
X 4.0 ON ON OFF ON
X 4.5 OFF ON OFF ON
X 5.0 ON OFF OFF ON
X 5.5 OFF OFF OFF ON
X 6.0 ON ON ON OFF

Example:

For Pentium II 400MHz CPU:
bus speed = 100MHz,
Core/Bus Ratio = X 4.0

the jumper settings should be: JP11:OFF,JB1:ON,JB2:ON,
JB3:OFF,JB4:ON

 

 

Bus Speed Selection (JP11)
JP11 (2-pin jumper) JP11 (3-pin jumper)
ON OFF (Default) OFF 1-2 2-3
66 MHz Auto (determined by CPU 66/100 pin) 100 MHz Auto (determined by CPU 66/100 pin) 66 MHz

 

  • CMOS/Battery:
    • JBT1: CMOS Clear, pin 1-2: Normal(default), pin 2-3: CMOS Clear (To clear CMOS needs to disconnect AC power.)
    • JBT2: Optional External battery, pin1: +3V, pin2 and pin3: No Connect, pin4: Ground
  • Front Control Panel:
    • JF1:
      • IDE LED: pin1:+5V, pin2:HD Active, pin3:HD Active, pin4:+5V
      • Power LED: pin5:Vcc +5V, pin6: Vcc +5V, pin7: Ground
      • Keylock: pin8: Keyboard Inhibit, pin9:Ground
      • Speaker: pin10: Vcc +5V, pin11 and pin12: No Connect, pin13:Speaker Data
    • JF2:
      • Infrared Connector: pin1:Vcc +5V, pin2: Key, pin3: IRRX, pin4:Ground, pin5:IRTX, pin6-pin8: No Connect
      • Power-ON: pin9: PW_ON, pin10: Ground, pin11:No Connect
      • Reset: pin12: Ground, pin13:Reset

     

  • SCSI:
    • SLED: SCSI LED Connector, pin1 and pin4 :Vcc, pin2 and pin3: SCSI LED# Signal
    • S_TERM: SCSI Termination, ON (default): Terminated, OFF: Un-terminated

 

  • Overheat/Thermal Control:
    • BZ_ON: Buzzer On, ON(default): Enable On-board Buzzer (Turn on the buzzer when overheat occurs), OFF: Disable On-board Buzzer
    • JOH1: Overheat LED Connector, pin1: Overheat Data, pin2: +12V

     

  • Power On Control:
    • JP20: Power_ON Control,
      • pin 1-2: Power Up Automatically With The First Time AC power Applied
      • pin 2-3 (default): Controlled By The Power_ON Jumper (JF2  pin9 and pin10).
    • WOL:Wake-On-LAN Connector, pin1: +5V Standby Power, pin2: Ground, pin3:Wake Up Pulse

     

  • Others:
    • JL1: Chassis Intrusion Connector, OFF: Default, ON: Intrusion (pin1: Intrusion Input, pin2:Ground)
    • J36: Extra Power Connector, pin1-pin3: Ground, pin4 & pin5: +3.3V, pin6: +5V
    • JP18 & JP16: Unused (OFF)

   

SUPER P6SBA JUMPER SETTINGS

  • CPU Settings:

CPU Core/Bus Ratio Jumper Settings
Ratio JB1 JB2 JB3 JB4
X 3.0 ON OFF ON ON
X 3.5 OFF OFF ON ON
X 4.0 ON ON OFF ON
X 4.5 OFF ON OFF ON
X 5.0 ON OFF OFF ON
X 5.5 OFF OFF OFF ON
X 6.0 ON ON ON OFF

Example:

For Pentium II 400MHz CPU:
bus speed = 100MHz,
Core/Bus Ratio = X 4.0

the jumper settings should be: JP11:OFF,JB1:ON,JB2:ON,
JB3:OFF,JB4:ON

 

 

Bus Speed Selection (JP11)
JP11 (2-pin jumper) JP11 (3-pin jumper)
ON OFF (Default) OFF 1-2 2-3
66 MHz Auto (determined by CPU 66/100 pin) 100 MHz Auto (determined by CPU 66/100 pin) 66 MHz

 

  • CMOS/Battery:
    • JBT1: CMOS Clear, pin 1-2: Normal(default), pin 2-3: CMOS Clear (To clear CMOS needs to disconnect AC power.)
    • JBT2: Optional External battery, pin1: +3V, pin2 and pin3: No Connect, pin4: Ground
  • Front Control Panel:
    • JF1:
      • IDE LED: pin1:+5V, pin2:HD Active, pin3:HD Active, pin4:+5V
      • Power LED: pin5:Vcc +5V, pin6: Vcc +5V, pin7: Ground
      • Keylock: pin8: Keyboard Inhibit, pin9:Ground
      • Speaker: pin10: Vcc +5V, pin11 and pin12: No Connect, pin13:Speaker Data
    • JF2:
      • Infrared Connector: pin1:Vcc +5V, pin2: Key, pin3: IRRX, pin4:Ground, pin5:IRTX, pin6-pin8: No Connect
      • Power-ON: pin9: PW_ON, pin10: Ground, pin11:No Connect
      • Reset: pin12: Ground, pin13:Reset

 

  • Overheat/Thermal Control:
    • BZ_ON: Buzzer On, ON(default): Enable On-board Buzzer (Turn on the buzzer when overheat occurs), OFF: Disable On-board Buzzer
    • JOH1: Overheat LED Connector, pin1: Overheat Data, pin2: +12V

     

  • Power On Control:
    • JP20: Power_ON Control,
      • pin 1-2: Power Up Automatically With The First Time AC power Applied
      • pin 2-3 (default): Controlled By The Power_ON Jumper (JF2  pin9 and pin10).
    • WOL:Wake-On-LAN Connector, pin1: +5V Standby Power, pin2: Ground, pin3:Wake Up Pulse

     

  • Others:
    • JL1: Chassis Intrusion Connector, OFF: Default, ON: Intrusion (pin1: Intrusion Input, pin2:Ground)
    • J36: Extra Power Connector, pin1-pin3: Ground, pin4 & pin5: +3.3V, pin6: +5V
    • JP18 & JP16: Unused (OFF)