MANUAIS DE MOTHERBOARDS SUPERMICRO

SUPER P5MMS98/P5MMS II/P5MMS Motherboard Jumper Settings

  
  SUPER P5MMS98             SUPER P5MMS II         SUPER P5MMS

 

SUPER P5MMS98 JUMPER SETTINGS

  • CPU Jumper Setting:

CPU Core/Bus Ratio Jumper Setting
Ratio J35 J36 J47
X 1.5 OFF OFF OFF
X 2.0 OFF ON OFF
X 2.5 ON ON OFF
X 3.0 ON OFF OFF
X 3.5 OFF OFF OFF
X 4.0 OFF ON ON
X 4.5 ON ON ON
X 5.0 ON OFF ON

Example:

For Intel's Pentium 233 MHz
MMX CPU :
bus speed = 66 MHz,
Core/Bus Ratio = X 3.5
CPU Vcore = 2.8 Volts

the jumper settings should be: JP5:1-2, JP6:2-3, JP7:2-3
J35:OFF,J36:OFF,J47:OFF,
J48:OFF, J49:OFF,
J50:OFF, J51:ON

 

Bus Speed Selection
Frequency JP5 JP6 JP7
50 MHz 2-3 2-3 2-3
60 MHz 2-3 2-3 1-2
66 MHz 1-2 2-3 2-3
75 MHz 2-3 1-2 1-2

CPU Core Voltage Setting

CPU Vcore

 J48 J49 J50 J51
2.1 Volts ON OFF OFF OFF
2.2 Volts OFF ON OFF OFF
2.3 Volts ON ON OFF OFF
2.4 Volts OFF OFF ON OFF
2.5 Volts ON OFF ON OFF
2.6 Volts OFF ON ON OFF
2.7 Volts ON ON ON OFF
2.8 Volts OFF OFF OFF ON
2.9 Volts ON OFF OFF ON
3.0 Volts OFF ON OFF ON
3.1 Volts ON ON OFF ON
3.2 Volts OFF OFF ON ON
3.3 Volts ON OFF ON ON
3.4 Volts OFF ON ON ON
3.5 Volts ON ON ON ON


  • CMOS/Battery:
    • JP2: CMOS Clear, pin 1-2: Normal(default), pin 2-3: CMOS Clear (To clear CMOS needs to disconnect AC power.)
    • JP3: Optional External battery, pin1: +3V, pin2 and pin3: No Connect, pin4: Ground

 

  • Front Control Panel:
    • J23:
      • IDE LED: pin1:+5V, pin2:HD Active, pin3:HD Active, pin4:+5V
      • Power LED: pin5:key, pin6:Vcc +5V, pin7: Vcc +5V, pin8: Ground
      • Keylock: pin9: Keyboard Inhibit, pin10:Ground
    • J57:
      • Power-ON: pin1: PW_ON, pin2: Ground
      • Reset: pin3: key, pin4:Ground, pin5:Reset, pin6: key
      • Speaker: pin7: Speaker Data, pin8 and pin9: No Connect, pin10: Vcc +5V

     

  • Overheat/Thermal Control:
    • JP15: Two-Pin Thermal Control Fan Connector, Pin 1: +12V, Pin 2: Ground (This fan is powered only when the CPU detected temperature is higher than the BIOS " CPU Overheat Warning Temperature" setting)
    • J53: Three-Pin Thermal Control Fan Connector, Pin 1: Ground, Pin 2: +12V, Pin3: Tachometer Signal
    • J45: Overheat LED Connector, Pin1: +12V, Pin2: Ground

     

  • Power On Control: (Only work with ATX power supply)
    • JP27: Power_ON Control,(Only work with ATX power supply)
      • pin 1-2: Power Up Automatically With The First Time AC power Applied
      • pin 2-3 (default): Controlled By The Power_ON Jumper (JF2  pin9 and pin10).
    • WOL:Wake-On-LAN Connector,(optional, Only work with ATX power supply)  pin1: +5V Standby Power, pin2: Ground, pin3:Wake Up Pulse

     

  • Others:
    • J7: BIOS Boot Block Protect, Pin1-2: Flashable(Default), Pin2-3: Protect,  J7 has to be set in position Pin1-2 when BIOS is to be flashed.
    • J37: USB Port Connector, pin1: Vcc +5V, pin2:P0-, pin3: P0+ pin4: Ground, pin5: key
    • J38: USB Port Connector, pin1: Vcc +5V, pin2:P0-, pin3: P0+ pin4: Ground, pin5: NC
    • J55: IRQ for PC Health monitor IC, NS LM78, Open: Default
    • J54:  Three-Pin CPU Fan Connector, Pin 1: Ground, Pin 2: +12V, Pin3: Tachometer Signal
    • J58:  Extra Three-Pin Fan Connector, Pin 1: Ground, Pin 2: +12V, Pin3: Tachometer Signal
    • J59: Chassis Intrusion Connector, OFF: Default, ON: Intrusion (pin1: Intrusion Input, pin2:Ground)
    • JP9: Serial Port, COM1, pin1:DCD, pin2: Serial In, pin3: Serial Out, pin4: DTR, pin5: Dround, pin6:DSR, pin7: RTS, pin8:CTS, pin9: RI, pin10: key
    • JP10: Serial Port, COM2, pin1:DCD, pin2: Serial In, pin3: Serial Out, pin4: DTR, pin5: Dround, pin6:DSR, pin7: RTS, pin8:CTS, pin9: RI, pin10: key
    • JP14: PS/2 Mouse Connector, pin1,2,3,5,8: NC, pin4: Clock, pin6: Vcc, Fused +5V, pin9: Ground, pin10: key
    • JP17: Fast Infrared Connector, pin1:Vcc +5V, pin2:NC, pin3: IRRX, pin4:Ground, pin5:IRTX, pin6: FIR_RX
    • JP18: Consumer Infrared Connector , pin1: Vcc +5V, pin2: IRTX, pin3: CIRRX, pin4: Ground

   

SUPER P5MMS II JUMPER SETTINGS

  • CPU Jumper Setting:

CPU Core/Bus Ratio Jumper Setting
Ratio J35 J36 J47
X 1.5 OFF OFF OFF
X 2.0 OFF ON OFF
X 2.5 ON ON OFF
X 3.0 ON OFF OFF
X 3.5 OFF OFF OFF
X 4.0 OFF ON ON
X 4.5 ON ON ON
X 5.0 ON OFF ON

Example:

For Intel's Pentium 233 MHz
MMX CPU :
bus speed = 66 MHz,
Core/Bus Ratio = X 3.5
CPU Vcore = 2.8 Volts

the jumper settings should be: JP5:1-2, JP6:2-3, JP7:2-3
J35:OFF,J36:OFF,J47:OFF,
J48:OFF, J49:OFF,
J50:OFF, J51:ON

 

Bus Speed Selection
Frequency JP5 JP6 JP7
50 MHz 2-3 2-3 2-3
60 MHz 2-3 2-3 1-2
66 MHz 1-2 2-3 2-3
75 MHz 2-3 1-2 1-2

CPU Core Voltage Setting

CPU Vcore

 J48 J49 J50 J51
2.1 Volts ON OFF OFF OFF
2.2 Volts OFF ON OFF OFF
2.3 Volts ON ON OFF OFF
2.4 Volts OFF OFF ON OFF
2.5 Volts ON OFF ON OFF
2.6 Volts OFF ON ON OFF
2.7 Volts ON ON ON OFF
2.8 Volts OFF OFF OFF ON
2.9 Volts ON OFF OFF ON
3.0 Volts OFF ON OFF ON
3.1 Volts ON ON OFF ON
3.2 Volts OFF OFF ON ON
3.3 Volts ON OFF ON ON
3.4 Volts OFF ON ON ON
3.5 Volts ON ON ON ON


  • CMOS/Battery:
    • JP2: CMOS Clear, pin 1-2: Normal(default), pin 2-3: CMOS Clear (To clear CMOS needs to disconnect AC power.)
    • JP3: Optional External battery, pin1: +3V, pin2 and pin3: No Connect, pin4: Ground

 

  • Front Control Panel:
    • J23:
      • IDE LED: pin1:+5V, pin2:HD Active, pin3:HD Active, pin4:+5V
      • Power LED: pin5:key, pin6:Vcc +5V, pin7: Vcc +5V, pin8: Ground
      • Keylock: pin9: Keyboard Inhibit, pin10:Ground
    • J57:
      • Power-ON: pin1: PW_ON, pin2: Ground
      • Reset: pin3: key, pin4:Ground, pin5:Reset, pin6: key
      • Speaker: pin7: Speaker Data, pin8 and pin9: No Connect, pin10: Vcc +5V

     

  • Overheat/Thermal Control:
    • JP15: Two-Pin Thermal Control Fan Connector, Pin 1: +12V, Pin 2: Ground (This fan is powered only when the CPU detected temperature is higher than the BIOS " CPU Overheat Warning Temperature" setting)
    • J53: Three-Pin Thermal Control Fan Connector, Pin 1: Ground, Pin 2: +12V, Pin3: Tachometer Signal
    • J45: Overheat LED Connector, Pin1: +12V, Pin2: Ground

     

  • Power On Control: (Only work with ATX power supply)
    • JP27: Power_ON Control,(Only work with ATX power supply)
      • pin 1-2: Power Up Automatically With The First Time AC power Applied
      • pin 2-3 (default): Controlled By The Power_ON Jumper (JF2  pin9 and pin10).
    • WOL:Wake-On-LAN Connector,(optional, Only work with ATX power supply)  pin1: +5V Standby Power, pin2: Ground, pin3:Wake Up Pulse

     

  • Others:
    • J7: BIOS Boot Block Protect, Pin1-2: Flashable(Default), Pin2-3: Protect,  J7 has to be set in position Pin1-2 when BIOS is to be flashed.
    • J37: USB Port Connector, pin1: Vcc +5V, pin2:P0-, pin3: P0+ pin4: Ground, pin5: key
    • J38: USB Port Connector, pin1: Vcc +5V, pin2:P0-, pin3: P0+ pin4: Ground, pin5: NC
    • J55: IRQ for PC Health monitor IC, NS LM78, Open: Default
    • J54:  Three-Pin CPU Fan Connector, Pin 1: Ground, Pin 2: +12V, Pin3: Tachometer Signal
    • J58:  Extra Three-Pin Fan Connector, Pin 1: Ground, Pin 2: +12V, Pin3: Tachometer Signal
    • J59: Chassis Intrusion Connector, OFF: Default, ON: Intrusion (pin1: Intrusion Input, pin2:Ground)
    • JP9: Serial Port, COM1, pin1:DCD, pin2: Serial In, pin3: Serial Out, pin4: DTR, pin5: Dround, pin6:DSR, pin7: RTS, pin8:CTS, pin9: RI, pin10: key
    • JP10: Serial Port, COM2, pin1:DCD, pin2: Serial In, pin3: Serial Out, pin4: DTR, pin5: Dround, pin6:DSR, pin7: RTS, pin8:CTS, pin9: RI, pin10: key
    • JP14: PS/2 Mouse Connector, pin1,2,3,5,8: NC, pin4: Clock, pin6: Vcc, Fused +5V, pin9: Ground, pin10: key
    • JP17: Fast Infrared Connector, pin1:Vcc +5V, pin2:NC, pin3: IRRX, pin4:Ground, pin5:IRTX, pin6: FIR_RX
    • JP18: Consumer Infrared Connector , pin1: Vcc +5V, pin2: IRTX, pin3: CIRRX, pin4: Ground
  • Difference Between SUPER P5MMS98 and SUPER P5MMS II:
    • Basically, SUPER P5MMS98 and SUPER P5MMS II are shared the same design, PCB and BIOS file.
    • SUPER P5MMS II does not assemble on-board PC Health Monitor IC (National Semiconductor's LM78).
    • Some items in BIOS "Peripheral" Section will be grayed out, if LM78chip   is not present.

   

SUPER P5MMS JUMPER SETTINGS

  • CPU Jumper Setting:

CPU Core/Bus Ratio Jumper Setting
Ratio J35 J36
X 1.5 OFF OFF
X 2.0 OFF ON
X 2.5 ON ON
X 3.0 ON OFF
X 3.5 OFF OFF

Example:

For Intel's Pentium 233 MHz
MMX CPU :
bus speed = 66 MHz,
Core/Bus Ratio = X 3.5
CPU Vcore = 2.8 Volts

the jumper settings should be: JP5:1-2, JP6:2-3, JP7:2-3
J35:OFF,J36:OFF, JP4: 2-3

Bus Speed Selection
Frequency JP5 JP6 JP7
50 MHz 2-3 2-3 2-3
60 MHz 2-3 2-3 1-2
66 MHz 1-2 2-3 2-3
75 MHz 2-3 1-2 1-2

CPU Core Voltage Setting

CPU Vcore

 JP4
2.8 Volts 2-3
3.3 Volts OFF
3.5 Volts 1-2
  • AMD K6-233/266 and K6-2 CPUs are not recommended to use with SUPER P5MMS.

 

  • CMOS/Battery:
    • JP2: CMOS Clear, pin 1-2: Normal(default), pin 2-3: CMOS Clear (To clear CMOS needs to disconnect AC power.)
    • JP3: Optional External battery, pin1: +3V, pin2 and pin3: No Connect, pin4: Ground
  • Front Control Panel:
    • J23:
      • Infrared Connector: pin1:Vcc +5V, pin2: Key, pin3: IRRX, pin4:Ground, pin5:IRTX, pin6: Mode, pin7-pin11: NC
      • IDE LED: pin12:+5V, pin13:HD Active, pin14:HD Active, pin15:+5V, Pin16:Key,Pin17:Key
      • Power LED: pin18:Vcc +5V, pin19: Vcc +5V, pin20: Ground
      • Keylock: pin21: Keyboard Inhibit, pin22:Ground
      • Speaker: pin23: Vcc +5V, pin24: No Connect, pin25: Buzzer, pin26:Speaker Data
    • J39:  Reset: pin1: Ground, pin2:Reset

     

  • Others:
    • J1: Alternative BIOS Boot Block Recover Area, Pin1-2: Default
    • J7: BIOS Boot Block Protect, Pin1-2: Flashable(Default), Pin2-3: Protect,  J7 has to be set in position Pin1-2 when BIOS is to be flashed.
    • J17,J28,J30: Manufacture Test Points, Default: OFF
    • J37: USB Port Connector, pin1: Vcc +5V, pin2:P0-, pin3: P0+ pin4: Ground
    • J38: USB Port Connector, pin1: Vcc +5V, pin2:P0-, pin3: P0+ pin4: Ground
    • J45: Overheat LED Connector, Pin1: +12V, Pin2: Ground
    • JP9: Serial Port, COM1, pin1:DCD, pin2: Serial In, pin3: Serial Out, pin4: DTR, pin5: Dround, pin6:DSR, pin7: RTS, pin8:CTS, pin9: RI, pin10: key
    • JP10: Serial Port, COM2, pin1:DCD, pin2: Serial In, pin3: Serial Out, pin4: DTR, pin5: Dround, pin6:DSR, pin7: RTS, pin8:CTS, pin9: RI, pin10: key
    • JP14: PS/2 Mouse Connector, pin1,2,3,5,8: NC, pin4: Clock, pin6: Vcc, Fused +5V, pin9: Ground, pin10: key