DO NOT UPGRADE YOUR BIOS IF YOU ARE USING PENTIUM PRO CPU WITH SLOT 1 ADAPTER CARD! VERSION 1.02 IS THE LATEST BIOS THAT WILL WORK WITH PENTIUM PRO CPU -V1.01 Initial release for P6LXA4 mainboard * FAN detection only -V1.02 * Add DMI Event LOG data structure for LDCM V3.1 * Added Fixed Disk Parameter Table Extension(FDPTE) * Dynamic config buffer strength for DRAM * Fix CPU overheat can not slow down the CPU * Fix DRAM ECC programming error * (Fix cannot FDISK under win95/win98--error only in internal testing) -V1.03 ( 1998/1/23 ) ---> Status : under testing * Fix Mylex DAC960 cannot work w/o PS/2 mouse ( DAC960 need XBDA ) * PCI slot IRQ can be selected by user * Remove add-on PCI-IDE setup and 2ND PCI-IDE setup ( For DC690 to work properly, user need to select the corresponding slot with DC690 for proper IRQ. If primary is configured, then IRQ14 must be selected. If secondary is configured, then IRQ15 must be configured. ) * Remove the following setup item ( These functions do nothing in previous release ). DRAM Read Around Write Burst Write Combining PCI-To-DRAM Pipelining Boot Up System Speed Gate A20 Option * Change Delay Transaction Default to be "Disabled". * Add HDD Smart Support * Add Deschutes CPU (CPUID 0650H) A0-stepping Micro-code Now, we have Micro-code for Pentium-II A0-stepping ( CPUID 630H ) Pentium-II B0-stepping ( CPUID 632H ) Pentium-II C0-stepping ( CPUID 633H ) Pentium-II C1-stepping ( CPUID 634H ) Deschutes A0-stepping ( CPUID 650H ) * Fix when enter green mode by green switch, then power off, then can not power on ( Need to pull out power cord and plug power to fix this problem ) * H/W monitoring option default to be disabled * Modified to use faster DRAM timing by default * Fix BTC CDROM DOS driver loading failed * Fix Quantum 12GB drive detecting error * Sync With Award 1998-1-20 BIOS NOTE: Since the DRAM timing is faster by deafult, if 75MHz/83MHz FSB speed is to be used, user may need to change the DRAM to slower timing for proper operation. -V1.04 ( 1998/4/13 ) * Add Celeron micro code support * Add PIIX4E support * Auto disable unused clock default to enabled * "Resume by ring" is changed to "Power up by ring/LAN" * "Resume by Alarm" is changed to "Power up by Alarm" * Change "Disable" to "Disabled" for Doze, Standby, Suspend Mode and HDD Power Down * MA Wait State Default To Slow to using Fujitsu SDRAM * Re-sysnc Award BIOS -V1.05 * Enable spread spectrum to reduce EMI ( Should enable "Auto Disable Unused Clock" item ) * Fix game G-NODE can not suspend under DOS * Fix time to suspend inaccurate * Change SYMBIOS SCSI BIOS to ver. 4.11.00 * Add Mendocino support ( with 128k L2 cache Celeron ) BIOS Display difference : Celeron 300MHz without L2 Cache --> CELEROM(TM)-MMX at 300MHz Celerom 300MHz 128K L2 Cache --> CELEROM(TM)-MMX at 300A MHz Celerom 333MHz 128K L2 Cache --> CELEROM(TM)-MMX at 333MHz * Add Trend-AntiVirus support * Change VGA Active Monitor to be disable ( Power management feature ) * Change Delayed Transaction Item default to "Enabled" Tekram SCSI CARD+TREND Boot AntiVirus Enabled+Boot from SCSI or Floppy ==> System Hang. Because Tekram BIOS will get error 21h port value. ==> Workaround for this condition: (1) Enable Delayed Transaction or (2) Disable Trend Boot AntiVirus detection Note : Tekram SCSI BIOS are planned to remove or modify OS/2 patch for interrupt mask operation to avoid this problem. -V1.06 * Fix bug for testing program REPORT.EXE ( Keyboard test ) -V1.06A ( Not a formal release version ) * Add delay ( 2 seconds ) before warm boot routine to reset system. Some power supply produces power noise and will cause some HDD's(Quantum) cache not flushed properly. This will cause the system to check disk or scandisk after re-start procedure. -V1.07 * Add support for Socket 370 Processor. ( Slot1 adapter board for socket 370 is required )