========================================== Date Version Description ========================================== 03-28-2000 1.00 S3PRO_M release 1.00 (CKS:707E) 03-23-2000 1.00j S3PRO_M adjust Rx51(0)=0 and rx64(6)=0 for 3DWINMARK 03-21-2000 1.00I S3PRO_M Fix Savage4 resume from S1 fail (use dsdt0216) 03-20-2000 1.00h S3PRO_M Fix Celeron 600 to show pIII 03-15-2000 1.00d S3PRO_A Remove 124/31 item when cpu is 133MHZ 03-15-2000 1.00g s3PRO_M 03-14-2000 1.00c S3PRO_A Remove PCICLK4 BUG definition 03-14-2000 1.00f s3PRO_M Fix Freq/150 can not be setup 03-10-2000 1.00e Fix AGP4x will enter in S3 and resume fail Fix CPU speed setup menu hang when 133 03-06-2000 1.00d Fix USB legcy enable in win98 and USB MOUSE+USB KEYBOARD plug in restart to MSDOS and Keyboard no wrok 03-03-2000 1.00d Fix USB legcy enable in win98 change "SDRAM Cycle Length" to "SDRAM CAS Latency" in BIOS SETUP 03-02-2000 1.00d add awdard pnp message display Fix USB legcy enable in DOS mode 02-23-2000 1.00C set VIA692 Reg51 bit 0=0 NCR_SETUP Item enable (pCIPOST) 02-23-2000 1.01E Fix Win982 to MSDOS USB keyboard not work when USb legacy enable when process ACPI OFF also clear USB SMI Fix resume from S3 and go to MSDOS, return to Win98 hang (SUS2DISK.asm) 02-18-2000 WINMAX 1.01 USE 1.01B3 version build 02-01-2000 S3AU 1.00b PCI4 CLK always Enable for H/W bug in BIOS.CFG set PCI4_CLK_BUG=1 01-27-2000 1.01D Fix win98 install hang when no AC97 codec (0112 new souce code) 01-10-2000 1.01B3 Fix USB/IRQ9 run awdflash.exe system hang retstart to MS-DOS from Win98 hang Set 694X R6Dh=25h,47h,47h, for #DIM1,2,3 01-05-2000 1.01B2 add "VCORE Control" item in Setup menu 01-03-2000 1.01B1 Fix Some AGP STR fail to resume (use 1229 pmupost.asm) 12-27-99 1.01(CKS:60A1)Normal release 1.01 12-24-99 1.0B8 Fix SCSI BOOT and restart to MSDOS from win98 Fail Fix SCSI BOOT and the slave HDD of primary channel not recognized in Win98 DRAM CLOCK 139Mhz->140MHz 12-21-99 1.0B7 Set "ACPI Function" item SHOWONLY DRAM CLOCK 67Mhz->66MHz Fix CD_ROM Boot Fail caused by 12-16-99 NT4.0 12-20-99 1.0B6 Remove "EDO DRAM at bank:" item in bios device listing 12-17-99 1.0B6 Fix remove/plugin power and sytem cannot Reboot When PowerFail option is ON(chipboot.inc) cause by 12-01 v1.0B4 side effect Fix CPU 133Mhz SW setting still work when change jumper into 100Mhz remove IDE device revision display 12-16-99 1.0B6 Fix NT40+2nd channel HDD booting slowly 12-15-99 1.0B5 Fix 686A-CD + Coopermine CPU Booting hang on 1DH Un-expected SMI occurred sometimes (pmupost.asm) 12-10-99 1.00 Fix IDE DETECTING FAIL WHEN 2nd IDE Channel is empty(hdinstal.asm) Fix GPO0=0 when CHKSUM ERROR 12-06-99 1.0B4 Change PCI IRQ Selectable Item String(PCIFEAT) ADD TNT2 DEVICE ID=0100H into compatibility Table 12-03-99 1.0B4 change 694x(CE) regB1=0xEC to 0xDA 12-03-99 1.0B4 Remove VCORE Voltage Control setup item 12-03-99 1.0B4 For AGP compatibility Set 694X(Reg6C bit6=1,Reg51 Bit2=1) S3-Virage RegB1=0xDA 12-02-99 1.0B4 NEC ZIP detecting none sometimes (HDINSTALL) 12-01-99 1.0B4 Fix Warm-Boot & remove/plugin power then sytem Reboot When PowerFail option is OFF(chipboot.inc) 11-30-99 1.0B4 Fix Anti-Virus enable and SCO reboot Hang (atorg.asm) 11-29-99 1.0B4 Fix USB printer not complete (Rx42 bit 2=1) (chiprun.asm) 11-24-99 1.0B4 Fix No FDD installed but there is FLoppY A: on desktop. Click on it then system waiting for response long time and seems to hang. (adisk.asm) (FDD_INSTALL_FLAG_SELTABLE =1 ) 14/15 display for PCI IDE DEVICE (xfile.asm) (SPECIAL_SHOW_IDE_DEVICE =1 ) DRAM 99Mhz ==>DRAM 100Mhz 11-17-99 1.0B3 USE 11-10-99 source code make v1.0B3 version Fix 66/100/133 CPU can not be exchanged Except remove 5V power Because SUSST1# is the same state on STR/Softoff Use GPO3 definition if system into S5. Add VIA_AGP_4X_Driving_Adjust definition to solve AGP problem 11-08-99 Fix DRAM CLOCK SHOW not correct if OVERDRIVE Fix TNT2 3DBENCH HANG (must SET 694x(Rx0b1h)=0ffh) 11-04-99 Fix ECC/PARITY ENABLE SYSTEM HANG BUG (MB1.0 HW IOCHK#) 11-02-99 Support kEYBOARD RESUME SETUP ITEM 11-01-99 Support VCore Setup item (gpo5) 10-29-99 Win98SE can not enter into S3 state(DSDT.asx) 10-28-99 ECC SDRAM/133 Fix ECC SDRAM/133 must set CAS=3 DRAM detecting change(Chipboot) 10-26-99 Use 10-25-99 sources v1.0B support two_usb_host VCM SDRAM fixed SDRAM show Bank 0,1 (DIMM0), Bank 2,3 (DIMM1)... 10-21-99 FIX SUSPEND LED not working in D3 mode (BIOS.CFG) 10-20-99 FIX WakeUp By Keyboard in poweroff/STR state (PMUPOST) Modify Modem RING Resume ==> WakeUp by LAN/Ring Item 10-19-99 FIX SUSPEND LED not working 10-18-99 Add VIO_Voltage Setting in SetUp Menu Fix VIA Audio testing fail problem Change Power Off /Power Fail Default setting Fix Power Fail message always display problem ADD GPO11,GPO8,GPO0 defintion 10-12-99 CMOS 40H can not be saved, moveall to other place(Cfeature) (DRAM CLK,MEMORY HOLE..) 10-08-99 SDRAM Show BANK0/BANK1 exchanged (chippost) modify Codec SUB_VID, SUB_SID (chippost) 10-07-99 Enable USB2 (chippost) Enable MC97 by Setting Rx44=C0h on Function 6 ADD SCSI BIOS ROM ADD Anti-Virus ROM PCI IRQ Selectable (PCIFEAT) 09-30-99 Resume Time ":" disapper (pfeature) Lpt mode default setting ECP/EPP(superio.pst) CPU/PCI Freqency auto detect (BIOS.CFG) 09-29-99 DRAM type Detection coding error (chipboot) Beep through Audio Codec (chiprun) Disable USB2 (chippost) AC97 audio/modem auto detection (chippost) AC97 audio/modem auto item (cfeature)