==========================================
Date Version Description
==========================================
05-05-2000 p6AU 1.03 (STANDARD)release 1.03 (CKS:B9F3)
05-05-2000 p6AU 1.03 (WINMAX) release 1.03 (CKS:9BB4)
04-28-2000 p6AU 1.02A(WINMAX) disable Suggest DRAM CLK /CAS Latency for
WINMAX
04-14-2000 S3MU 1.00 S3PRO-MU v1.00 release CS:F93CH
04-05-2000 S3AU 1.00 S3PRO-AU v1.00 release (CKS:FEF5)
03-28-2000 S3MU 1.00a
03-24-2000 S3AU 1.00f Fix USBKB+USBMICE and enter win982E sometimes
hang (when USB KB enable in BIOS SETUP)
03-23-2000 S3AU 1.00e Fix 1.00d win98 install hang and STR problem
03-22-2000 S3AU 1.00d Add VCORE control setup item
Fix Celeron 600 Mhz display error
change "SDRAM Cycle Length" to
"SDRAM CAS Latency" in BIOS SETUP
Remove 124/31 item when cpu is 133MHZ
Remove PCI4_CLK_BUG=1 definition in bios.cfg
03-03-2000 p6AU 1.02 (WINMAX) release 1.02
02-25-2000 1.00c fix 686A-CG version USB legacy enable bug
02-23-2000 p6AU 1.01E display pnp message
fix SCSI item disable problem
fix usb kb legacy enable and restart to msdos
from win982E and usb kb not work
02-23-2000 S3AU 1.00c display pnp message
fix SCSI item disable problem
fix usb kb legacy enable and restart to msdos
from win982E and usb kb not work
02-01-2000 S3AU 1.00b PCI4 CLK always Enable for H/W bug
in BIOS.CFG set PCI4_CLK_BUG=1
01-27-2000 1.01D Fix win98 install hang when no AC97 codec
(0112 new souce code)
01-10-2000 1.01B3 Fix USB/IRQ9 run awdflash.exe system hang
retstart to MS-DOS from Win98 hang
Set 694X R6Dh=25h,47h,47h, for #DIM1,2,3
01-05-2000 1.01B2 add "VCORE Control" item in Setup menu
01-03-2000 1.01B1 Fix Some AGP STR fail to resume (use 1229
pmupost.asm)
12-27-99 1.01(CKS:60A1)Normal release 1.01
12-24-99 1.0B8 Fix SCSI BOOT and restart to MSDOS from win98
Fail
Fix SCSI BOOT and the slave HDD of primary channel
not recognized in Win98
DRAM CLOCK 139Mhz->140MHz
12-21-99 1.0B7 Set "ACPI Function" item SHOWONLY
DRAM CLOCK 67Mhz->66MHz
Fix CD_ROM Boot Fail caused by 12-16-99 NT4.0
12-20-99 1.0B6 Remove "EDO DRAM at bank:" item in bios
device listing
12-17-99 1.0B6 Fix remove/plugin power and sytem cannot
Reboot When PowerFail option is ON(chipboot.inc)
cause by 12-01 v1.0B4 side effect
Fix CPU 133Mhz SW setting still work when change
jumper into 100Mhz
remove IDE device revision display
12-16-99 1.0B6 Fix NT40+2nd channel HDD booting slowly
12-15-99 1.0B5 Fix 686A-CD + Coopermine CPU Booting hang on 1DH
Un-expected SMI occurred sometimes (pmupost.asm)
12-10-99 1.00 Fix IDE DETECTING FAIL WHEN 2nd IDE Channel is
empty(hdinstal.asm)
Fix GPO0=0 when CHKSUM ERROR
12-06-99 1.0B4 Change PCI IRQ Selectable Item String(PCIFEAT)
ADD TNT2 DEVICE ID=0100H into compatibility Table
12-03-99 1.0B4 change 694x(CE) regB1=0xEC to 0xDA
12-03-99 1.0B4 Remove VCORE Voltage Control setup item
12-03-99 1.0B4 For AGP compatibility
Set 694X(Reg6C bit6=1,Reg51 Bit2=1)
S3-Virage RegB1=0xDA
12-02-99 1.0B4 NEC ZIP detecting none sometimes (HDINSTALL)
12-01-99 1.0B4 Fix Warm-Boot & remove/plugin power then sytem
Reboot When PowerFail option is OFF(chipboot.inc)
11-30-99 1.0B4 Fix Anti-Virus enable and SCO reboot Hang (atorg.asm)
11-29-99 1.0B4 Fix USB printer not complete (Rx42 bit 2=1)
(chiprun.asm)
11-24-99 1.0B4 Fix No FDD installed but there is FLoppY A:
on desktop. Click on it then system waiting for
response long time and seems to hang. (adisk.asm)
(FDD_INSTALL_FLAG_SELTABLE =1 )
14/15 display for PCI IDE DEVICE (xfile.asm)
(SPECIAL_SHOW_IDE_DEVICE =1 )
DRAM 99Mhz ==>DRAM 100Mhz
11-17-99 1.0B3 USE 11-10-99 source code make v1.0B3 version
Fix 66/100/133 CPU can not be exchanged Except remove 5V power
Because SUSST1# is the same state on STR/Softoff
Use GPO3 definition if system into S5.
Add VIA_AGP_4X_Driving_Adjust definition to solve AGP problem
11-08-99 Fix DRAM CLOCK SHOW not correct if OVERDRIVE
Fix TNT2 3DBENCH HANG (must SET 694x(Rx0b1h)=0ffh)
11-04-99 Fix ECC/PARITY ENABLE SYSTEM HANG BUG (MB1.0 HW IOCHK#)
11-02-99 Support kEYBOARD RESUME SETUP ITEM
11-01-99 Support VCore Setup item (gpo5)
10-29-99 Win98SE can not enter into S3 state(DSDT.asx)
10-28-99 ECC SDRAM/133 Fix
ECC SDRAM/133 must set CAS=3
DRAM detecting change(Chipboot)
10-26-99 Use 10-25-99 sources v1.0B
support two_usb_host
VCM SDRAM fixed
SDRAM show Bank 0,1 (DIMM0), Bank 2,3 (DIMM1)...
10-21-99 FIX SUSPEND LED not working in D3 mode (BIOS.CFG)
10-20-99 FIX WakeUp By Keyboard in poweroff/STR state (PMUPOST)
Modify Modem RING Resume ==> WakeUp by LAN/Ring Item
10-19-99 FIX SUSPEND LED not working
10-18-99 Add VIO_Voltage Setting in SetUp Menu
Fix VIA Audio testing fail problem
Change Power Off /Power Fail Default setting
Fix Power Fail message always display problem
ADD GPO11,GPO8,GPO0 defintion
10-12-99 CMOS 40H can not be saved, moveall to other place(Cfeature)
(DRAM CLK,MEMORY HOLE..)
10-08-99 SDRAM Show BANK0/BANK1 exchanged (chippost)
modify Codec SUB_VID, SUB_SID (chippost)
10-07-99 Enable USB2 (chippost)
Enable MC97 by Setting Rx44=C0h on Function 6
ADD SCSI BIOS ROM
ADD Anti-Virus ROM
PCI IRQ Selectable (PCIFEAT)
09-30-99 Resume Time ":" disapper (pfeature)
Lpt mode default setting ECP/EPP(superio.pst)
CPU/PCI Freqency auto detect (BIOS.CFG)
09-29-99 DRAM type Detection coding error (chipboot)
Beep through Audio Codec (chiprun)
Disable USB2 (chippost)
AC97 audio/modem auto detection (chippost)
AC97 audio/modem auto item (cfeature)