| DARWIN-Q Main B/D CMOS SETUP | |||
| 사용 키 | |||
| Help | F1 | ||
| Back | ESC | ||
| Select | Enter | ||
| Previous Item | 위 방향 키 | ||
| Next Item | 아래 방향키 | ||
| Select Menu | 좌, 우 방향 키 | ||
| Setup Default | F5 | ||
| Previous Values | F6 | ||
| Save & Exit | F10 | ||
| 부팅 시 F1 KEY 누름 | |||
| 1단계 | 2단계 | 3단계 | 선택 옵션 |
| Main | System Date | 날자 설정 | |
| System Time | 시간 설정 | ||
| Floppy Options | Press Enter | ||
| Floppy A | 360K 5.¼/ 1.2M 5.¼ / | ||
| Floppy B | Not/ 720KB ½ / 1.44M ½ / 2.88M ½ | ||
| Primary IDE Master | 선택된 디바이스 명 표시 | ||
| IDE Device Configuration | Auto Configured, User Definable, Disabled | ||
| IDE Translation Mode | Standard CHS, Logical Block, Auto Detect | ||
| Multiple Sector Setting | Disabled, 4Sector/Block, 8Sectors/Block, Auto Detected | ||
| Fast Programmed I/O Modes | Disabled, Auto Detected | ||
| Primary IDE Slave | IDE Device Configuration | Auto Configured, User Definable, Disabled | |
| IDE Translation Mode | Standard CHS, Logical Block, Auto Detect | ||
| Multiple Sector Setting | Disabled, 4Sector/Block, 8Sectors/Block, Auto Detected | ||
| Fast Programmed I/O Modes | Disabled, Auto Detected | ||
| Secondary IDE Master | IDE Device Configuration | Auto Configured, User Definable, Disabled | |
| IDE Translation Mode | Standard CHS, Logical Block, Auto Detect | ||
| Multiple Sector Setting | Disabled, 4Sector/Block, 8Sectors/Block, Auto Detected | ||
| Fast Programmed I/O Modes | Disabled, Auto Detected | ||
| Secondary IDE Slave | IDE Device Configuration | Auto Configured, User Definable, Disabled | |
| IDE Translation Mode | Standard CHS, Logical Block, Auto Detect | ||
| Multiple Sector Setting | Disabled, 4Sector/Block, 8Sectors/Block, Auto Detected | ||
| Fast Programmed I/O Modes | Disabled, Auto Detected | ||
| Language | English (US) | ||
| Boot Options | Press Enter | ||
| First Boot Device | Disabled, Floppy, Hard Disk, CD-ROM, Network | ||
| Second Boot Device | Disabled, Floppy, Hard Disk, Network | ||
| Third Boot Device | Disabled, Floppy, Hard Disk, Network | ||
| Fourth Boot Device | Disabled, Floppy, Hard Disk, Network | ||
| System Cache | Enabled, Disabled | ||
| Boot Speed | Deturbo, Torbo | ||
| Num Lock | Off, On | ||
| Speaker | Enabled, Disabled | ||
| Setup Prompt | Disabled, Enabled | ||
| Hard Disk Pre-Delay | Disabled, 3/6/9/12/15/21/30 Seconds | ||
| Typematic Rate Programming | Default, Override | ||
| Typematic Rate Delay | 250msec, 500msec, 750msec, 1000msec | ||
| Typematic Rate | 6, 8, 10, 12, 15, 20, 24, 30 char/sec | ||
| Scan User Flash Area | 이 항목은 사용하지 않음. | ||
| Advanced | Processor Type | CPU Type 표시 | |
| Processor Speed | CPU 속도 표시 | ||
| Cache Size | Cache 용량 표시 | ||
| Peripheral Configuration | Press Enter | ||
| Primary IDE Interface | Auto, Disabled, Enabled | ||
| Secondary IDE Interface | Auto, Disabled, Enabled | ||
| Floppy Interface | Auto, Disabled, Enabled | ||
| Serial Port1 Address | Disabled, COM1 3F8 IRQ4, COM2 2F8 IRQ3, COM3 3E8 IRQ4, COM4 2E8 IRQ3, COM1 3F8 IRQ3, COM2 2F8 IRQ4, COM3 3E8 IRQ3, COM4 2E8 IRQ4, Auto | ||
| Serial Port2 Address | Disabled, COM1 3F8 IRQ4, COM2 2F8 IRQ3, COM3 3E8 IRQ4, COM4 2E8 IRQ3, COM1 3F8 IRQ3, COM2 2F8 IRQ4, COM3 3E8 IRQ3, COM4 2E8 IRQ4, Auto | ||
| Serial Port 2 IR Mode | Disabled, Enabled | ||
| Parallel Port Address | Disabled, LPT3 3BC IRQ7, LPT1 378 IRQ7, LPT2 278 IRQ 7, LPT3 3BC IRQ5, LPT1 378 IRQ5, LPT2 278 IRQ5, Auto | ||
| Parallel Port Mode | Compatible, Bi-directional, ECP, EPP | ||
| USB interface | Disabled, Enabled | ||
| Hardware Monitor Interface | Disabled, Enabled | ||
| Primary IDE Status | Enabled | ||
| Secondary IDE Status | Enabled | ||
| Floppy Status | Enabled | ||
| Serial Port1 Status | COM1 3F8 IRQ4 | ||
| Serial Port2 Status | COM2 2F8 IRQ3 | ||
| Parallel Port Status | LPT1 378 IRQ7 | ||
| Advanced Chipset Configuration | Press Enter | ||
| Base Memory Size | 640KB | ||
| ISA LFB Size | Disabled, 1MB | ||
| Video Palette Snoop | Disabled, Enabled | ||
| Latency Timer(PCI Clocks) | Auto-Configured | ||
| Bank 0 SIMM Detected | None Installed | ||
| Bank 1 SIMM Detected | EDO | ||
| Power Management Configuration | Press Enter | ||
| Advanced Power Management | Disabled, Enabled | ||
| IDE Drive Power Down | Disabled, Enabled | ||
| VESA Video Power Down | Disabled, Standby, Suspend, Sleep | ||
| Inactivity Timer(Minutes) | 0 ~ 256(기본 10) | ||
| Hot Key(Ctrl - ALT -) | |||
| Auto Start On AC Loss | Disabled, Enabled | ||
| Power Down COM1 Ring | Disabled, Enabled | ||
| Plug and Play Configuration | Press Enter | ||
| Configuration Mode | Use Setup Utility 선택 시 | ||
| ISA Shared Memory Size | Disabled: ISA Card 설명서 참조 | ||
| IRQ 5 | Available, Used by ISA Card | ||
| IRQ 9 | Available, Used by ISA Card | ||
| IRQ 10 | Available, Used by ISA Card | ||
| IRQ 11 | Available, Used by ISA Card | ||
| IRQ 12 | Available, Used by ISA Card | ||
| Plug and Play Configuration | Configuration Mode | Use Setup Utility 선택 시 | |
| ISA Shared Memory Size | C8000h, CC000h, D000h, D4000h, D8000h, DC000h | ||
| IRQ 5 | Available, Used by ISA Card | ||
| IRQ 9 | Available, Used by ISA Card | ||
| IRQ 10 | Available, Used by ISA Card | ||
| IRQ 11 | Available, Used by ISA Card | ||
| IRQ 12 | Available, Used by ISA Card | ||
| Plug and Play Configuration | Configuration Mode | Use ICU 선택 시 | |
| Boot with PnP OS | PnP정보의 BIOS or OS 설정 | ||
| Non | PnP정보를 BIOS에서 지정 | ||
| Other | PnP정보를 다른 OS에서 지정 | ||
| Windows 95 TM | PnP정보를 Win95에서 지정 | ||
| Event Logging Configuration | Event Log Status | Valid | |
| Log Capacity | Available | ||
| Count Granularity |
10 |
||
| Time Granularity(minutes) |
30 |
||
| Log Control | Enabled | ||
| Clear Log | No | ||
| Mark Exiting Event Read | No | ||
| Critical Event in Log : | |||
| Sigle Bit ECC Errors | None | ||
| Multiple Bit ECC Errors | None | ||
| Post Errors | |||
| Security | User Password is | Disabled | |
| Administrative Password is | Disabled | ||
| Set User Password | Press Enter | ||
| Enter Current Password | |||
| Enter New Passwod | |||
| Confirm New Password | |||
| Set Administrative Password | Press Enter | ||
| Enter Current Password | |||
| Enter New Passwod | |||
| Confirm New Password | |||
| Unattended Start | Enabled, Disabled | ||
| Security Hot Key(CTRL- ALT-) | |||
| Exit | Exit Saving Changes | Press Enter | |
| Exit Discarding Change | Press Enter | ||
| Load Setup Default | Press Enter | ||
| Discard Change | Press Enter | ||
{button DARWIN-Q 관련 항목 보기, Klink(DARWIN-Q)}