PINE TECHNOLOGY PT-606E Card Type Controller card Maximum Onboard Memory Unidentified Hard Drives supported Two IDE (AT) drives Floppy drives supported Two 360KB, 720KB, 1.2MB, or 1.44MB drives I/O Options Floppy drive interface, game port, IDE interface (2), parallel port, serial ports (2) Data Bus 16-bit ISA Card Size Half-length, full-height CONNECTIONS Function Label Function Label 40-pin secondary CN1 10-pin serial port 2 - CN6 IDE(AT) connector internal 40-pin primary IDE(AT) CN2 25-pin parallel port - CN7 connector external 34-pin cable connector CN3 2-pin connector - primary JP6 - floppy drive IDE drive active LED 9-pin serial port 1 - CN4 2-pin connector - JP7 external secondary IDE drive active LED 16-pin game port - CN5 internal USER CONFIGURABLE SETTINGS Function Label Position » Game port enabled J1 Pins 1 & 2 closed Game port disabled J1 Pins 2 & 3 closed » Floppy drive interface enabled J3 Pins 1 & 2 closed Floppy drive interface disabled J3 Pins 2 & 3 closed » Primary IDE enabled J5 Pins 1 & 2 closed Primary IDE disabled J5 Pins 2 & 3 closed » Secondary IDE enabled J6 Pins 1 & 2 closed Secondary IDE disabled J6 Pins 2 & 3 closed » External floppy enabled J12 Pins 1 & 2 closed External floppy disabled J12 Pins 2 & 3 closed » ECP enabled J13 Pins 1 & 2 closed ECP disabled J13 Pins 2 & 3 closed » Factory configured - do not alter J14 Pins 1 & 2 closed » Factory configured - do not alter J17 Unidentified » IOCHRDY signal enabled JP3 Closed IOCHRDY signal disabled JP3 Open » IDE channels use same IDE LED JP5 Closed IDE channels use separate IDE LEDs JP5 Open PARALLEL PORT ADDRESS SELECTION Setting J4 » LPT1 (378h) Pins 1 & 2 closed LPT2 (278h) Pins 2 & 3 closed SERIAL PORT ADDRESS SELECTION Setting J7 J8 J9 J10 COM1 (3F8h) Pins 1 & 2 Pins 1 & 2 N/A N/A closed closed COM2 (2F8h) N/A N/A Pins 1 & 2 Pins 1 & 2 closed closed COM3 (3E8h) Pins 1 & 2 Pins 2 & 3 N/A N/A closed closed COM4 (2E8h) N/A N/A Pins 1 & 2 Pins 2 & 3 closed closed Disabled Pins 2 & 3 N/A Pins 2 & 3 N/A closed closed INTERRUPT SELECTION IRQ (Send) IRQ (Receive) JP4 3 3 Pins 11 & 12 closed 3 4 Pins 10 & 11 closed 4 3 Pins 8 & 9 closed 4 4 Pins 7 & 8 closed 5 3 Pins 5 & 6 closed 5 4 Pins 4 & 5 closed 9 3 Pins 2 & 3 closed 9 4 Pins 1 & 2 closed PARALLEL PORT MODE SELECTION Setting J2 J11 » SPP Pins 2 & 3 closed Pins 1 & 2 closed ECP Pins 1 & 2 closed Pins 1 & 2 closed EPP Pins 1 & 2 closed Pins 2 & 3 closed DACK/DRQ SELECTION Setting DACK DRQ J15 J16 » SPP N/A N/A Pins 5 & 6 Pins 1 & 2 closed closed ECP/EPP 3 1 Pins 1 & 2 Pins 3 & 4 closed closed ECP/EPP 3 3 Pins 3 & 4 Pins 5 & 6 closed closed