Return to MAIN-Index  Return to SUB-Index    IBM-AUSTRIA - PC-HW-Support    30 Aug 1999

Auto Setup for the Gt3i, GXT15O, or GXT15OL Adapter



Auto Setup for the Gt3i, GXT15O, or GXT15OL Adapter

To perform auto setup for the Gt3i, GXT15O, or GXT15OL Adapter:
  1.  Turn on the monitor.
  2.  Turn on the RS/6000. The screen remains blue until the RS/6OOO  is ready. This is not a problem.

     If an error message is displayed

     If the message UNSUPPORTED VIDEO is displayed or nothing is  displayed at all, check that:

  3.  When the AIX desktop login screen is displayed, log in as the  root user, type diag from the AIX command prompt, and press Enter. If you  cannot see the login prompt, adjust the brightness and contrast.

     Wait for about 15 minutes, until the monitor warms up.

    NOTE: If the monitor is in standby mode ("STANDBY ON"), it might  automatically turn off while you are waiting for it to warm up.  Exit standby mode (refer to the explanation of STANDBY).

     About the panels

     The RS/6000 panels differ according to the diagnostic software  level. The following details about the panels are only examples.

     The system diagnostic panel (number 801001) is displayed. The  number is displayed on the upper right corner of the screen.

      +--------------------------------------------------------------------------------+
      |IBM RISC System/6000 POWERstation and POWERserver                       801001  |
      |DIAGNOSTICS VERSION 1.0                                                         |
      |LICENSED MATERIAL and LICENSED INTERNAL CODE - PROPERTY OF IBM.                 |
      |(C)     COPYRIGHTS BY IBM AND BY OTHERS 1982,1993.                              |
      |ALL RIGHTS RESERVED.                                                            |
      |DIAGNOSTIC OPERATING INSTRUCTIONS                                               |
      |                                                                                |
      |These programs contain diagnostic and service aids for the system.              |
      |These procedures should he used whenever problems with the system occur         |
      |which have not been corrected by any software application procedures            |
      |available.                                                                      |
      |                                                                                |
      |In general, the procedures will run automatically. However, sometimes           |
      |you will be required to select options,inform the system when to                |
      |continue, do simple tasks, and exchange diskettes.                              |
      |                                                                                |
      |Several keys are used to control the procedures;                                |
      |    -- The Enter key continues the procedure or performs an action.             |
      |    -- The Backspace key allows keying errors to be corrected.                  |
      |    -- The cursor keys are used to select an option.                            |
      |Press the F3 key to exit or press Enter to continue.                            |
      +--------------------------------------------------------------------------------+
     

  4.  Press Enter to display the Function Selection menu (number 801002).  Move the cursor to Service Aid.

      +--------------------------------------------------------------------------------+
      |FUNCTION SELECTION                                                      801002  |
      |                                                                                |
      |Move cursor to selection, then press Enter.                                     |
      |                                                                                |
      |Diagnostic Routines                                                             |
      |         This selection will test the machine hardware and detect any hardware  |
      |         problems. A problem will be indicated by a SRN (Service Request Number)|
      |         The SRN will allow a service representative to quickly determine what  |
      |         parts are required to repair the machine.                              |
      |                                                                                |
      |Service Aid                                                                     |
      |         This selection will look at the machine configuration, exercise        |
      |         external interfaces, format media, look at past diagnostic results,    |
      |         control what resources are tested, check out media, etc.               |
      |                                                                                |
      |Advanced Diagnostic Routines                                                    |
      |         This selection will normally be used only by the service               |
      |         representative.                                                        |
      |                                                                                |
      |                                                                                |
      |                                                                                |
      |F3--Cancel      FI0=Exit                                                        |
      +--------------------------------------------------------------------------------+
     

  5.  Press Enter. The Service Aids Selection menu (number 802001) appears:

      +--------------------------------------------------------------------------------+
      |SERVICE AIDS SELECTION                                                  802001  |
      |                                                                                |
      |Move cursor to selection and press Enter.                                       |
      |                                                                                |
      |(TOP)                                                                           |
      |                                                                                |
      |Service Hints                                                                   |
      |        This selection displays service hints and errata information about      |
      |        the maintenance package.                                                |
      |                                                                                |
      |Display Previous Diagnostic Results                                             |
      |        This selection displays the results of previous diagnostic runs.        |
      |                                                                                |
      |Display or Change Configuration or Vital Product Data(VPD)                      |
      |        This selection displays or changes the configuration or VPD.            |
      |                                                                                |
      |Display or Change Diagnostic Test List                                          |
      |        This selection displays the resources tested by Diagnostics and         |
      |        allows the resources to be added or deleted from the Diagnostic Test    |
      |        List.                                                                   |
      |                                                                                |
      |Disk Media                                                                      |
      |        This selection provides the format disk and certify disk service        |
      |        aids.                                                                   |
      |                                                                                |
      |Diskette Media                                                                  |
      |       This selection provides a tool for checking out a diskette.              |
      |                                                                                |
      |Service Aids for Use With Ethernet                                              |
      |       (Ethernet is a trademark of Xeros Corp.)                                 |
      |                                                                                |
      |(MORE.. .13)                                                                    |
      |                                                                                |
      |F3=Cancel F10=Exit                                                              |
      +--------------------------------------------------------------------------------+
     

  6.  Press PageDown to display the second page of the menu. Move the cursor to Display Test Patterns.

      +--------------------------------------------------------------------------------+
      |SERVICE AIDS SELECTION                                                  802001  |
      |                                                                                |
      |Move cursor to selection and press Enter.                                       |
      |                                                                                |
      |(MORE.. .13)                                                                    |
      |                                                                                |
      |This selection provides a tool for checking out a diskette.                     |
      |                                                                                |
      |Service Aids for Use with Ethernet                                              |
      |          (Ethernet is a trademark of Xerox Corp.) This selection provides      |
      |          a tool for diagnosing Ethernet problems.                              |
      |                                                                                |
      |SCSI Bus                                                                        |
      |          This selection provides a tool for diagnosing SCSI bus problems.      |
      |                                                                                |
      |Display Test Patterns                                                           |
      |          This selection displays patterns required to adjust the IBM 5081 and  |
      |          IBM 6091 displays.                                                    |
      |                                                                                |
      |Microcode Download                                                              |
      |          This selection provides a tool for downloading microcode from a       |
      |          diskette to a fixed disk.                                             |
      |                                                                                |
      |Product Topology                                                                |
      |          This selection updates the system Product Topology information.       |
      |          It should be run whenever the system is installed, when a MES of FCSI |
      |          is installed and when a FRU is exchanged.                             |
      |                                                                                |
      |(BOTTOM)                                                                        |
      |                                                                                |
      |F3=Cancel FlO=Exit                                                              |
      +--------------------------------------------------------------------------------+
     

  7.  Press Enter to display panel 802081. Move the cursor and select the connected video adapter.

      +--------------------------------------------------------------------------------+
      |DISPLAY SERVICE AID                                                     802081  |
      |                                                                                |
      |Which of the following displays do you want to test?                            |
      |                                                                                |
      |Move cursor to selection, then press Enter.                                     |
      |                                                                                |
      |The color display attached to the GXT 150 Graphics Adapter                      |
      |    in Location 0O-DJ.                                                          |
      |                                                                                |
      |Return to the Service Aids Selection Menu.                                      |
      |                                                                                |
      |F3=Cancel  F1O=Exit                                                             |
      +--------------------------------------------------------------------------------+
     

  8.  Press Enter to display panel 802087. Move the cursor to The color-bar pattern.

      +--------------------------------------------------------------------------------+
      |DISPLAY SERVICE AID                                                     802087  |
      |                                                                                |
      |Which of the following displays do you want to test?                            |
      |                                                                                |
      |Move cursor to selection, then press Enter.                                     |
      |                                                                                |
      |   The red full screen pattern.                                                 |
      |   The green full screen pattern.                                               |
      |   The blue full screen pattern.                                                |
      |   The black full screen pattern,                                               |
      |   The white full screen pattern.                                               |
      |   The 9 A 7 grid pattern.                                                      |
      |   The 9 A 11 grid pattern.                                                     |
      |   The colorbar pattern.                                                        |
      |   The 50mm box pattern.                                                        |
      |   Return to the Display Selection menu.                                        |
      |   Return to the Service Aids Selection menu.                                   |
      |                                                                                |
      |F3=Cancel F10=Exit                                                              |
      +--------------------------------------------------------------------------------+
     

  9.  Press Enter, and panel 802084 is displayed:

      +--------------------------------------------------------------------------------+
      |DISPLAY SERVICE AID                                                     802084  |
      |                                                                                |
      |The Pattern you selected will be displayed on the next screen.                  |
      |                                                                                |
      |REMEMBER .....to use 'Cancel'  to exit the screen.                              |
      |                                                                                |
      |To display the pattern, press Enter.                                            |
      |                                                                                |
      |F3-Cancel F1O=Exit                                                              |
      +--------------------------------------------------------------------------------+
     

  10.  Press Enter. The color-bar pattern is displayed on the screen.

     
  11.  Push the setup switch on the back of the monitor:
     The setup main menu appears in front of the color-bar pattern:

     
  12.  Push one of the contrast control buttons.

     The messages are automatically displayed in the following  sequence:
     "OFF">"READY">"START">"COMPLETED"
     and auto setup is complete.

     If the screen flickers, go back to step 11 and redo the setup  several times until flickering is minimized. If the problem persists,  adjust manually by doing manual setup (see Appendix A).

     The screen might be distorted during setup. This is not a  problem.

     It "AUTO SETUP COMPLETED" is not displayed

     Go back to step 11 and redo auto setup. If the setup procedure  does not complete successfully, an "AUTO SETUP FAILED"  message appears. If this message appears, repeat the auto setup  procedure up to three times.

     If after retrying three times, you are unable to complete the setup,  perform manual setup, or contact the Display  Business Unit (DBU) helpline.

     If, after you perform auto setup, the display is still  distorted, perform  manual setup described in Appendix A.

  13.  Check the following for the color-bar pattern. If there is  anything wrong, push one of the contrast control buttons and repeat the  auto setup procedure.

  14.  Set the power management mode settings whenever necessary.
     (See The Setup Main Menu.)
  15.  Press F3 to exit the color-bar pattern.
  16.  Push the setup switch on the back of the monitor to turn off  the setup main menu.


You have completed the monitor setup.


Back to  Jump to TOP-of-PAGE
More INFORMATION / HELP is available at the  IBM-HelpCenter

Please see the LEGAL  -  Trademark notice.
Feel free - send a Email-NOTE  for any BUG on this page found - Thank you.